Search results

Hi, We have a WFM 125 wessex flail mower for a compact tractor and the main right angle gearbox went on it last week. The teeth have been stripped off the crown wheel gear somehow. Its about two months out of warranty and so no help from the manufacturers. Would anyone know where i could look...

Hi, I was wondering if anybody had been automatically entered into an electricity contract by a broker. We have just been entered into a contract. They said they sent notification by email but we didn't receive anything They said we cant get out of it as we didn't opt out of the emails they...

Hi I need a few engine parts for an old perkins engine. Diperk have a minimum £15 charge who else can i go to? I need a few bits and pieces but dont want to buy things unnecessarily each time to get to £15. Front crank seal is the first thing which is £6/7. TIA RAF

Hi, We have a 1980 Yale diesel forklift that I have had to strip the LH brake drum down. In doing so i have had to undo the pipe fitting into the brake shoe actuator. Its a male compression fitting securing a steel pipe something more akin to a car brake system. I think its UNF but how would i...

Hi, We have a plug in wifi system made by Devalo that sends the internet signal from the router down the electrical wiring of the house and are picked up by devices plugged into the sockets in various different rooms. The wifi signal is then sent around the room from the plug socket device. I...

Grounds speed radar has packed up on our puma 240. It's about £900 from Case. Is there anywhere else that i can buy one to suit the tractor? Its been deleted off the tractor for now. TIA

Hi, We have a set of Simba 23C discs. I have been told that the thread on the main drawbar pin at the discs end of the drawbar is 1 3/4 inch BSW. Does anybody know where I can get such a rare beast. Kverneland want a lot of money for it. Cheers RAF

Hi, My navara needs a new drivers seat. Nissan dont have any so i need help finding a breaker with some in stock. Does anybody know of breakers doing Navaras? Cheers

Hi, have we had a thread on this? Just wondering what it's all about. I assumed the changes would only affect bad landlords who would look to treat tenants poorly, but i hear that landlords are selling houses off due to the rules that may come in. Anybody know much about this? RAF

Hi, I need to get rid of some tractor tyres about 8 in total. Possibly some old super singles too. Prices vary when ringing round so could do with a recommendation for a disposal recycling company. We are in the west mids and would be happy to deliver them if needs be. Thanks RAF

Hi, I was hoping for some advice. We have two 75m valley gutters which occasionally drip on a few of the joints. The gutters are 40 years old asbestos type and aren't going to get any better with age so i was thinking of getting them lined with an aluminium seamless lining. Would this be the...

Wanted to take the chain off to check it for wear but the ops book just refers to tensioning. Am I missing something, I Thought the three augers needed timing when putting a chain on but cant see where it tells you to do it in the book. Thanks for any pointers. cheers

Hi, Just seeing if anybody else has had steering issues with their Sp Sprayer. It would seem the circuit boards become an issue. Ive had a look at ours and i think it could be that the way the box containing the circuit board is mounted in the engine compartment it is subject to quite alot of...

Hi, Question is as the thread title really. We've got a bit of wear in the cam clutch shaft splines on this power harrow and so looking to change it for a new one. I cant identify it on the Walterscheid website as there are a number of them and so was wondering if anybody knew which type it...

If you take down a tired old portal frame building from circa the 1970s that's past its sell by date, and rebuild something that is almost identical on the footprint can you claim tax relief as a repair? TIA

Is it possible to hire powerful vacuums like the big brute machines. I've got a couple of sheds that need a clean up. It's mainly all dust and chaff sitting on the sheeting rails. A weeks hire would do it.

Heard that this might be happening and they're currently looking to completely replace it.

Has anybody splashed out on a welding/cutting respirator or helmets with one built in. Haven't had a look yet but thinking of getting one so any recommendations would be appreciated. TIA

We have quite a bit of slug pelleting to do and it would be nice to spread to 24m. Don't really want a boom spreader so do any broadcasters manage it?? The electric ones need to be fairly high up to stand a chance so it seems, and so that rules out the quad mounted stuff?? TIA

Hi, Just wondering if there was a specialist supplier of Simba parts like specially made pins and bushes, bearings, hydraulic seals etc. I gather Kverneland do them now ( is this right?) so is it just go to the closest dealer or do Kverneland have a dedicated warehouse/parts store for Simba...