We have a newholland t7050 split. The main drive shaft going to engine seems to be broken inside the box. Has anyone seen that before or what has caused it?
Have a 7050 autocommand that wont go forward. If u push it forward on the shuttle gradually sometimes it jumps in with a bang nearly but it wont do that often just throws up neutral after a few seconds. I can get it to reverse a bit but its slipping out of it too but i can make it reverse all...
Had a voltage drop on an autocommand and its lost a few calibrations. Have a 5015 for pto anyone any idea how calibrate it through the hh menu? Also have one for steering angle sensor and the diff
Bought a set of 560/60/22.5 Tyres for a tankers around Xmas. So far iv had to return 3 because of bulges appearing on the thread of the tyre. I have never had a full set on and currently my last returned one has been gone 6weeks. If blew out 2 worn 560s if had to run to make up the set to keep...
As above rear pto on 7050 wouldn't start all of a sudden first it was codes 5034 5035 relating to fender pto button issues. So I turned them off through the diagnostic plug and all was fine. Soon after it was 5003 pto brake solenoid. Changed that and it cured 5003. But I had to turn off the pto...
I have noticed my pump running noisier this past while and the other day I checked oil level to find it low where id never even had to top it up in 4 seasons. Is mechanical seal gone? I topped it up and its getting away very very slowly. I never touched the pump in 4 years is there anything else...
All of a sudden iv lost reverse on my shuttle. It goes it to reverse ok when I use button on joystick. Forward is fine. Any ideas? Tractor is an autocommand
front suspension is down again too seem to have never ending problems with it is there anything simple to check with it?
Have a 210 autocommand that wont go through the ranges. As ot goes into the second range it slips into neutral. It serns to go tp around 4mph and then when I go above that itll drop into neutral. No codes only during calibration I get u97 which idicates clutch f2 did not engage. Have changed...
I seem to have bad pressure on spool valves but when I press brake pedal its ok. Whats going on here? Sometimes lift arms suddenly drop aswell any ideas? No errors
Im looking at putting in a lagoon to hold in region of half a million gallons. Based in NI has anyone any companys theyd recommend for the job? Bit of a toss up between it or an above ground tower but id imagine the lagoon is a much cheaper option
Anyone with experience of shearbar removal? My dealer told me they needed to replace my shearbar as it could not be turned because a bolt broke when removing it. I have never took one off myself and havent had a minute to remove head to see the setup but I cant imagine that this true? Shearbar...
Had a couple of wrecks lately due to stone damage knives ripped out shearbar etc whats peoples experience with farmers insurance on this? Put it through my own last year after a bad one but cant stick that anymore
Im running the above sower hydraulic driven. All of a sudden it seems to be sowing stripy. Iv sowed thousands of acres with it and am fairly certain it was set up correctly. It seems to be sowing light at one side. The fins seem smooth and not worn to my knowledge anyway. The control box shows...
Any common issues on t7 aircons. Mine just blowing warm air. Gas is fine. Guy reckons its either dryer unit blocked slightly or evaporater valve blocked.
A while ago just before xmas to be precise I sold a slurry tanker. The guy was from southern ireland im in NI. He paid in cash and gave me an eu vat no so no vat was due. I ran the check at the time an it was valid. Now almost 6months later hmrc are on to me looking the vat paid over as its now...
Possibly a stupid question but does anyone no is there a seperate windscreen water holder for the front? Iv 2 not working on the front this while and the backs work fine obviously if theres water in them
Having a few problems towards end of last season with stuff getting in behind knives and blocking. So I guess its time to tighten the springs? I haven't touched it in 3 seasons and never had to open it before. So has anyone a fairly comprehensive guide on doing this job or any tips? Im told its...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.