Forums
New posts
Forum list
Search forums
What's new
New posts
New resources
Latest activity
Trending Threads
Resources
Latest reviews
Search resources
FarmTV
Farm Compare
Search
Tokens/Searches
Calendar
Upcoming Events
Members
Registered members
Current visitors
New Resources
New posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Forum list
Search forums
Menu
Log in
Register
Navigation
Install the app
Install
More options
Contact us
Close Menu
Forums
Farm Machinery
Workshop Projects
Deere cab trim
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="clbarclay" data-source="post: 1411930" data-attributes="member: 6671"><p>John its simple enough when you know what your doing. I expect the redesign was mainly to help reduce assembly time. It went back together fairly easily and quickly once I worked out how its mean to go back together. Its just that moment where a haynes manual would just tell you to "unfasten the pannel" and your left thinking 'so how the F do I do that'.</p><p></p><p></p><p></p><p>[USER=5919]@Mursal[/USER], I'm bearly a voice for radio, let alone a face for video and refitting trim with one hand while filming with the other is a level of multi tasking far higher than I'm willing to try. However...</p><p></p><p>The side pannel is held in place by:</p><p>The top edge and side against the door tucked under other pannels.</p><p>Two press clips at the bottom near the seat. Circled in purple/blue</p><p>The hard plastic part held by three plastic nuts underneath, covered by floor. Circled in green.</p><p>The hard plastic part by the mat is clipped through the softer pannel, but I didn't bother seperating them.</p><p></p><p>[ATTACH]178282[/ATTACH]</p><p>[ATTACH]178284[/ATTACH]</p><p></p><p>Studs for the nuts circled in green and holes for the clips circled in purple.</p><p>[ATTACH]178286[/ATTACH]</p><p></p><p>To remove the pannel first as [USER=992]@Jd Everytime[/USER] posted, remove the trim infront of the seat holding the floor matt and pull the mat back. To make untucking it from under the consol easier, start by lifting and pulling it from by the A post.</p><p></p><p>Unscrew the 3x 10mm plastic nuts and unclip the pannel by reaching under the bottom edge around each clip and pulling towards the seat.</p><p>[ATTACH]178288[/ATTACH]</p><p>(Swearing at the tractor without realising it)</p><p></p><p>Ease the pannel out in the general direction of the brake pedals to remove it. Refitting is broadly speaking the revese of removal, taking a bit of riggling to get it tucked in right against the door surround and then under the rest of the console top, before refastening.</p><p></p><p></p><p>The hardest part was finding a decent app just to draw a few circles on photos, followed by getting the ez-piolt harness to fit back neatly in the channel cut out of the underside of the matt.</p><p></p><p>The trim all survived and its nice to get the cables tucked a lot neater out of the way.</p><p>[ATTACH]178302[/ATTACH]</p><p></p><p>Thanks all for the advice.</p></blockquote><p></p>
[QUOTE="clbarclay, post: 1411930, member: 6671"] John its simple enough when you know what your doing. I expect the redesign was mainly to help reduce assembly time. It went back together fairly easily and quickly once I worked out how its mean to go back together. Its just that moment where a haynes manual would just tell you to "unfasten the pannel" and your left thinking 'so how the F do I do that'. [USER=5919]@Mursal[/USER], I'm bearly a voice for radio, let alone a face for video and refitting trim with one hand while filming with the other is a level of multi tasking far higher than I'm willing to try. However... The side pannel is held in place by: The top edge and side against the door tucked under other pannels. Two press clips at the bottom near the seat. Circled in purple/blue The hard plastic part held by three plastic nuts underneath, covered by floor. Circled in green. The hard plastic part by the mat is clipped through the softer pannel, but I didn't bother seperating them. [ATTACH]178282[/ATTACH] [ATTACH]178284[/ATTACH] Studs for the nuts circled in green and holes for the clips circled in purple. [ATTACH]178286[/ATTACH] To remove the pannel first as [USER=992]@Jd Everytime[/USER] posted, remove the trim infront of the seat holding the floor matt and pull the mat back. To make untucking it from under the consol easier, start by lifting and pulling it from by the A post. Unscrew the 3x 10mm plastic nuts and unclip the pannel by reaching under the bottom edge around each clip and pulling towards the seat. [ATTACH]178288[/ATTACH] (Swearing at the tractor without realising it) Ease the pannel out in the general direction of the brake pedals to remove it. Refitting is broadly speaking the revese of removal, taking a bit of riggling to get it tucked in right against the door surround and then under the rest of the console top, before refastening. The hardest part was finding a decent app just to draw a few circles on photos, followed by getting the ez-piolt harness to fit back neatly in the channel cut out of the underside of the matt. The trim all survived and its nice to get the cables tucked a lot neater out of the way. [ATTACH]178302[/ATTACH] Thanks all for the advice. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Farm Machinery
Workshop Projects
Deere cab trim
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top