- Location
- Lancashire
light drizzle at 5 this morning, eased off to get some in the pens .mid nov … should give you just enough time to sweep shed and set up pens for lambing
See how long back owds out
Coming Home For Lambing.
- Thread starter Gator
- Start date
See how long back owds out
Bloodhell your in a roll, 2....
Did 60 odd yesterday, jus 1 sticky one. Shed some lambs of some early doors, done 20 so far, brew un bacon butty time
If I get 50 done today I'll be happy by the time I've wrapped the wool un all
I did half of hogs yesterday an then shears bust, i'm just not cut out for this shearing malarkey
- Location
- Lancashire
Got a pair of these ya can borra
[emoji23] I've got some of them[emoji23] joking aside there really good though [emoji106]Got a pair of these ya can borra
[emoji23][emoji23][emoji23][emoji23][emoji23]
- Location
- Lancashire
Nowt clipped today couldn't get um dry enough so had a ride round the nexnext lot on the more see if outs blown, seem all great so far.
Couple of hours int workshop and knocked these up.
Quick raid in the scrap pile
Bit of old 4 inch box some silage rap tide, bit of tin and flat bar and fannys yar ant
115 quid each + the dreaded at north sheep, cant see that mi self.
Think a should go into production, easier than clipping sheep
so had a ride round the nexnext lot on the more see if outs blown, seem all great so far.Couple of hours int workshop and knocked these up
.
Quick raid in the scrap pile
Bit of old 4 inch box some silage rap tide, bit of tin and flat bar and fannys yar ant
115 quid each
+ the dreaded at north sheep, cant see that mi self.Think a should go into production, easier than clipping sheep
- Location
- Dumfries & Galloway
Tidy!
What the holes for?
Ye must like yer paint. I just use 1 can... sparingly
What the holes for?
Ye must like yer paint. I just use 1 can... sparingly
- Location
- Lancashire
Holes are so I could get screwdriver in un screw the tubes to the plateTidy!
What the holes for?
Ye must like yer paint. I just use 1 can... sparingly
, some how I cant seem to to weld the plastic tube before it melts. Plenty of red oxide
- Location
- Dumfries & Galloway
Holes are so I could get screwdriver in un screw the tubes to the plate
Ahhhh makes sens!!
I'd have used a small bolt, and just put the spanner in from the top
- Location
- Lancashire
I've counter sunk the selftaper screw on the inside so as not to catchAhhhh makes sens!!
I'd have used a small bolt, and just put the spanner in from the top
- Location
- Dumfries & Galloway
Perfectionist
- Location
- Lancashire
- Location
- Lancashire
Last of the second batch in for shedding, poor drying day, didnt get started till after 2 ish, goin dark by time there done
Rained most of night so nowt clipped today, Gather the third batch up later
Rained most of night so nowt clipped today, Gather the third batch up later
Steel
Member
- Location
- Finley, Riverina, Australia
We sometimes have problems with shearers stopping for wet sheep when there has been no rain. Usually young Australian shearers wanting a day off. NZers don’t call wet sheep unless the sheep are wet, and we have one local Scottish shearer who says he has rarely seen a wet sheep in Australia. He says if you won’t shear wet sheep, you wont ever shear sheep in Scotland.
- Location
- Lancashire
Its abit different from last year, I'd finished shearing and half way through haymaking
- Location
- Lancashire
Gathered the last batch for tomorra.......if it dont rain
Makes a change gathering in a T shirt
Makes a change gathering in a T shirt
- Location
- Lancashire
- Location
- Lancashire
Bloody typical, jus starting to rain
- Location
- Lancashire
Houdini in for a trim, yep she's still wick and doing well
and doing well
