• Welcome to The Farming Forum!

    As part of this update, we have made a change to the login and registration process. If you are experiences any problems, please email [email protected] with the details so we can resolve any issues.

Recent content by jpn

  1. jpn

    Full Trimble RTK sprayer installation with section control for sale

    See attached photo of all the parts.
  2. jpn

    Full Trimble RTK sprayer installation with section control for sale

    Morning all, we have changed our batemand sprayer from a Trimble to John Deere system. So we have a full installation kit which was taken off of it for sale. It compromises of: 1x CFX-750 TRIMBLE DISPLAY WITH RTK AND HARNESSES 1X TRIMBLE EZ STEER & HARNESSES (SAM 200) 1X 12 SECTION SWITCH...
  3. jpn

    How to calibrate your own Marconi moisture metre for crop assurance.

    The only one our maconi (933A) fails on is the leakage test. In the cells (we have 2 cells to try) it reads 0.65 - with the leads not plugged into anything it reads 0.6. and if I unplug the leads of the meter then it's reads right at the bottom of the scale below -0.6 How do we go about sorting...
  4. jpn

    How to calibrate your own Marconi moisture metre for crop assurance.

    Thanks for the reply, good to know lots of spares are still available. If we do want another set of cells and leads, what sort of price and how do we go about getting them from you? Thanks, Jake
  5. jpn

    How to calibrate your own Marconi moisture metre for crop assurance.

    @Lodekka we have a tf933a, when calibrating it it's spot on 40 with a 1MOhm resistor, but on the continuity it's probably high 60s/70? It's this reading either shorting the female terminals on the meter, or shorting the block in the clamp. So internal issues? Any ideas, we have 3 of these so...
  6. jpn

    Potato Price Tracker

    We have a 1 1/4 tonne spare of Soraya 45-55mm if anyone's interested?
  7. jpn

    How to set up your own RTK base station.. for about £300

    I don't think my one showed up immediately, try going directly to it, type in http://rtk2go.com:2101/SNIP::MOUNTPT?baseName=RadwellRTK, but instead of "RadwellRTK" put in your base name. I think mine took a few days to show in the table, but it did show if I went directly to it.
  8. jpn

    How to set up your own RTK base station.. for about £300

    Have you been emailed a authorised password from them yet? If not then you have to use the generic one till you do which is "WEEK2311".
  9. jpn

    How to set up your own RTK base station.. for about £300

    Could be because it's not sending out a stable signal. They say on their site that if this happens your IP may be temporarily banned.
  10. jpn

    Anyone know a RTK2GO or centipede caster which works for John Deere mrtk?

    No worries it's connected and now working!
  11. jpn

    Anyone know a RTK2GO or centipede caster which works for John Deere mrtk?

    Do you know what messages JD needs? As I will need to know that when we setup ours
  12. jpn

    Anyone know a RTK2GO or centipede caster which works for John Deere mrtk?

    About 30km away - Yes I've tried connecting to that, but same problem, if you run that and can change it that would be perfect.
  13. jpn

    Anyone know a RTK2GO or centipede caster which works for John Deere mrtk?

    Hi I'm just trying to get mrtk working on our starfire 6000 and before setting up our own base I want to know it's all working on someone elses. So does anyoke know of a RTK2GO or centipede base which works with johndeere. I've tried connecting to a few of them but the best I get is the orange...
  14. jpn

    How to set up your own RTK base station.. for about £300

    Brilliant, ok I've got a modem coming for our 6000 end of the week, so can check then. Thanks
Back
Top