Search results

Hi All, i hope someone can help with this. i have a 2006/7 678 combi baler that i bought in a non working state. there were sensors missing etc. i replaced these and got it working and it works just fine exept it will not "Auto Start" the wrapping cycle, i have to press "Start Cycle" on the...

Hi all. I have an old Dowdeswell DP6 plough that I have just bought. I need some mouldboards which I am being told are Lemken LWU. any ideas where to get them? also does anyone know how to set it up and where I might find the towing frame? Thanks

Hi all. I have a 1997 MF 6180 dynashift. It has developed a noise when driving aiming like a chain is being dragged along the ground. It doesn't change much if at all when I put it into 4wd, if I go really slow it doesn't do it but any thing over 5mph and you can hear it more often than not...

Hi. I have a fastrac that is leaking engine oils from what appears to be the rear main seal. Has anyone removed an engine from one before? If so, did I grange the transmission off in place or out eurgh the engine? Thanks in advance

Hi all, I have a 1997 6180 in reasonable condition but just lately the big warning light on the left of the dash has started to come on along with the hydraulic oil pressure light. this in turn changes the dynashift to its default position (D) and fires the tractor up the road or into what ever...

hi all, my 6180 has the low oil pressure light coming on intermittently. ive been straw carting this week, when i drive about 3-4 miles on the road then stop and work in the field as soon as i depress the clutch the light comes on, it defaults to D on the dynashift, the 4WD light comes on and...

Hi all. I'm having real issues with my 6180 just lately, last night after 30 min of working/driving i stopped the engine for a couple of minutes and when I started it back up there was a couple of loud knocks that sounded like they came from the bell housing area. It done this Every time there...

Hi all. When I slow down I get a loud chattering from the rear end. This also happens when going down hills. The brakes also go almost to the floor too but still stop good. The clutch / hydraulic system makes a whirling noise too Any ideas?

Hi all. I have a mf 6180 which until now was working fine but I now have the A and D lights flashing together on the dynashift display. Can anyone help? It still drives forward ave backwards but in one gear. Thanks in advance Ash

I'm looking at getting some cattle in to fill a space. I dont want anything that is going to take a lot to look after I.e calf's but also don't want them to cost the earth when I but them. Any suggestions?

Hi all. The couch on my 6180 went weird, it used to feel like it had 2 stages then one day it started to get ready fierce, I press the 4wd button like I thread on hear suggested abs it was better. I eventually got a new accumulator and fitted it, feels a different tractor all together, it's...

Hi all. Anyone have any ideas as to why a spool calve would seam to put pressure up a return line after a couple of minutes? I was using my wrapper and after a couple of minutes the table stops and both pipes are pressurised. It stays like it for a minute I'm moving the lever back and forth...

Hi all. My tractor is running hotter that normal. I had a read leak of of which I replaced. Then the water pump was replaced and I took the thermostats out and it still does it. The heater in the can however does not work. There is also no water up there. Does anyone know how to bleed the...

Hi all. I had an issue with my pto playing up. Now my gearbox is too. When I select low range from high the gear stick is almost impossible to move, I have to hit it in either direction quite firmly to get it to free off so I can change gear. Has anyone else had this?

Hi all, I have recently purchased a 1997 6180 Dynashift. In having an issue whereby occasionally (7 out of 10 times) when I disengage the PTO the gears jump to D through to The gear im in I.e b or a. Has anyone experienced this before? Thanks

Hi everyone, My 3080 has started to pulse through the pedal when applying the brakes. also now and again when pulling away really slow and turning the steering wheel on full lock it feels like the tractor has a really hard job to pull away, when i dip the clutch it stops dead! anyone have an...

Hi everyone, I have an 1989 3080 autotronic with a problem with low range. i have a isolator switch fitted because the range light ( hare ) and the 4wd light stays on and drains the battery, when i switch the tractor on it automatically selects low range by as i think it should but when in...

I have a 644 baler. I have replaced at the relevant bearings that cause any problems. I'm in the process of replacing 2 belts but the book says they are 8712 mm but the old ones are 8600 mm And the new ones are sagging badly. Can anyone shed any light on this? Ash