Hi, does anyone know if a quicke 10.70 will fit onto a set of newer (2012) brackets. Am I right in saying it is a DM loader so wide fit? Looking to put it onto a massey 7495.
Hi, for some reason the vistronic fan on my 7495 has lost communication with the tractor causing it to lockup and run flat out permanently. Aside from the noise it also means its sucking unnecessary dust into the radiator. I've checked the plugs and all seem OK, I have a 5 volt supply down to...
Help! Tractor won't move because it thinks the handbrake is on when it isn't. Unlike a lot of tractors the switch is on the brake caliper rather than the hand brake lever. Going to try a new switch but I'm not convinced it's that. Is there a hidden fuse somewhere as there are no allocations in...
Hi, looking at changing my new holland BB960 for another baler a bit newer. The newer one I'm interested in is a BB960A, 2007 double axle with rear steer and it's on 500/50-17 tyres. My current baler is 2001 double axle with no rear steer but has been fitted with bigger 540/45r22.5 tyres. Axles...
How do I go about changing the track width on my 7495? It's fitted with the bar axle (picture below) I'm guessing undo the 4 bolts which will release the wedges but then is it a case of brute force to slide the hub in or out on the bar?
Bit of a long shot but would anyone happen to know the diameter across to the outside edges of part number 8? It's the sealing discs on the end of the first roller after the rotor in the bottom of the baler. I'm looking for two with a diameter of 230mm for another job I'm doing. Local dealer...
I recently purchased a 3095 dynashift with electrical gremlins, would only drive in low box and stuck in dynashift D. Traced it down to the two yellow wires feeding the autotronic box had corroded away, replaced the join where go down to one wire and job sorted. Took the tractor for a spin up...
I'm looking to control a relay using the headland management on the data3 screen of my 7495. Can't find any mention in the manuals of where the socket is that supplys the signal. Anyone know? And also which pin please.
Large square baler: New Holland - D1010 Silage
Category: Large square baler Manufacturer: New Holland Price: £4250 Condition: Used
Description:
New Holland D1010 Silage big square baler, 1993. 4 String 80x90 bale size.
Been converted to run bale density from tractor spools so no...
Got a bb960 and two of the knotters will wrap the twine around the bill hook shafts. I have advanced the twine discs as far as I dare which helped and I have also found replacing the quick release pins on the knotters with bolts has helped. I'm guessing I have some wear somewhere but the...
Hi, changing the backend oil and filters in my 7495 tomorrow. Whilst I have the oil drained I am going to change the cardon shaft brake discs as a precaution as I only purchased the tractor last year. Anyone have any tips on doing it? I already have the discs soaking in oil.
I know it's still a bit early but thinking about getting a swath roller to put on the front of the baling tractor. Had a fair bit of hassle last year with stuff rolling up underneath the tractor and baler hitch. Did look into making my own but then came across these
Does anyone have one and...
Hi, the climate control up in the roof on my 7495 is dead. First time I have used the tractor for a few weeks, went to put the heater going and nothing happens. The screen is blank and I have no lights or fan blowing. I have tested the big 50 amp fuse and that's fine, swapped the relay in the...
Hi, anyone got any ideas why my brake pedal has started pulsing when I apply the brakes. It only does it once warm and not all the time. If I apply the brakes very gently it won't do it and also if I am towing something with trailer brakes it doesn't do it. :scratchhead:
My 7495 has decided to have a funny five minutes randomly selecting reverse on its own whilst travelling forward! Not much fun when it did it to me the first time going down the road! When it does it the error codes D135 or D136 will flash up, these relate to the shuttle lever voltages so with...
Hi, I have an issue with the electric spools on my 7495. Sometimes when they are in the float position they will pulse making the hydraulic pipes of the baler jump. When they are doing it you can see the manual lever on the spools moving in and out of float position. It will do it repeatedly...
I have a 90 degree gearbox on my quadrant baler and there is a fair amount of backlash between the crown wheel and pinion. This is a common problem on them and can supposedly be sorted by shimming out the slack. I have had a look in the box and removed the seal and circlip from behind the pinion...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.