Search results

Hi has anyone had a similar fault on a manitou with a Deutz engine. No throttle I suspected a throttle pedal fault but it seems to test ok on JALTEST. And apparently not uncommon for wiring issues..

Hi got a manitou MT732 with a duetz engine and the throttle is sat at a raised ideal speed and won’t rev up. Has anyone had any issues with the throttle pedal potentiometers.

Hi has anyone got a wiring Diagram for a John Deere 7700 Tractor. Happy to pay.!! Any help appreciated

Hi can anyone help with a couple of faults on a Cushman hauler Pro 72 volt buggy. The charger isn’t working and showing a 6 flash code which I believe is an internal charger fault. Is there anything else to check before we order. Charger. Also the BDI isn’t reading battery voltage does the BDI...

Hi all.. has anyone got any knowledge of a Kramer 418. We have one with sluggish drive in forward. Carried out a stall pressure test and in reverse stall pressure is at 4300 psi and she pushes well and spins the wheels.. and in forward stall pressure is higher at 6000 psi but with no push and...

Hi all.. has anyone got any knowledge of a Kramer 418. We have one with sluggish drive in forward. Carried out a stall pressure test and in reverse stall pressure is at 4300 psi and she pushes well and spins the wheels.. and in forward stall pressure is higher at 6000 psi but with no push and...

Can anyone help with these faults codes on a Manitou SLI error fault i have the details for the later SLI fault list but not for the earlier machines..!

Hi we have a customer with a Kramer KT356 and it won’t crank when it’s cold.. if you keep clicking the key it then cranks over and starts. Is there anything common on these.. possible start relay faults or seat switch..!

Hi can anyone help with the calibration of the forward speed on a new Holland TS115A. Got a customer with one and the battery went flat and the forward speed doesn’t read correctly. I would imagine there is a set up in the Menu.. does anyone one what menu address you need tk go in to.. many...

hi does anyone know what voltage should be at the low pressure switch on a late 3080 Massey.. got one that is playing up.. installed the new type switch and was working ok but Playing up again.. only got 4.8 volts.. out of the computer under the step.. checked connections as I know they suffer...

Hi we have a skyjack SJ6832RT that has sluggish drive.. mainly shows up when on rougher ground and when the platform is raised past to speed cut back switch it struggles to drive.. we have changed many parts as the original fault was a failed needle bearing in the front left hand drive motor...

Hi can anyone help with an on going error fault on a Kubota M7151. We have had the main fuse / relay board repaired as were told that was the fault and a new one isn’t available but we still have the same codes coming up.!!

Can anyone assist with these codes on a Kubota M7151.. had the main relay / fuse board sent away as was told that was the problem but we still have the same codes coming up.. checked connections and voltages all seems ok..

Got a customer reporting a SLI fault with a manitou. The alternator failed and the batteries went completely flat. Changed the alternator and now the SLI is flashing three lights.. is it because the calibration has been lost on the SLI unit.!!

Got a customer John Deere 2036 compact tractor with a fault where the engine cuts out when you put it into gear.. I’m thinking seat switch fault has anyone had this problem

We have a customers 5465 and it suddenly stopped.. the injection pump fuse had blown.. replaced the fuse but still won’t start.. tried to communicate with the jeltest diagnostics but can’t get it to communicate and can’t see any can signal on the cad loom or diagnostics plug.. checked all feeds...

Hi can anyone assist for a customer machine with an intermittent fault showing brake pressure low.. and apparently the brakes feel poor at the same time.!! Any thoughts appreciated

Hi has anyone had similar issues with a John Deere 7700 with HCU Error code 052 draft sensor voltage.. I have checked through the wiring and suspecting and computer fault..

Hi got a customer with a JCB Teletruck with a kohler engine the drive doesn’t completely cut out on tick over is there any transmission adjustment we can do or and way of lowering the rock over.. but it’s fly by wire throttle.!!

Evening has anyone got a new or good secondhand pick up hitch hook insert or complete hitch for a JCB 531-70..