I have a taarup Straw blower. This u bolt has broke. It's for the floor chains.
Is this a standard thing one can buy in a hardware shop or is it a genuine piece only? Anyone hardly have the part number?
Have a taarup 832 straw chopper. Need a new hydraulic ram for the shoot on the swivel blower.ram is to direct the shoot higher and lower.
It's a small ram. Genuine part is mega money. Where could I get a spurious? Dealer was saying its 40 bore and 120 stroke if that makes sense?
So got a new manuka oil pressure gauge put into my hitatchi digger today. The one with capillary tube.
Is has an Isuzu 4bd1 turbo engine in it. It read the following pressures. At start up it was about 40 psi. Then worked it for an hour to get it hot. When left idling at working temperature it...
Have an isuzu 4bd1 turbo in my hitatchi digger. Is anyone here familiar with it? Where can I plug in an oil pressure gauge to get the psi it's working at?
There are these little squares in it. I can hardly plug into them?
https://klr.com.au/store/land-rover/perentie-and-110/engine-isuzu-4bd1/oil-system-and-filters/spin-on-oil-filter-housing-4bd1/
The sensor coming out the bottom of the housing - what would that be telling? Oil pressure or oil temperature?
Is there any good air freshers/cleaners you can buy to give the cab a nice clean fresh smell as if it has just been valeted. Not a rotten magic tree type thing that u hang from the mirror but something you spray and wipe around the place? Are those grassmen chrome products any good?
Is it much if a job to install all the wiring for indicators into a machine from scratch? Have an old vintage tractor and all the wiring and indicators have been taken off it years ago. Wondering would it be a big job to redo all the wiring and switches for the indicators all from scratch
What is worn in this massey 860 backhoe for this to move back and forward. The rest of the machine has had new pins and bushings everywhere and this seems to be the only place with a bit of wear.
Old Hitachi digger here. It has a 4 cylinder turbo Isuzu 4bd1t engine in it. The engine is gone in it.
I have access to a very good Isuzu 6bb1 straight engine for more or less free. Would this engine ever bolt on or will it be totally different?
I have an overum cx 4 furrow reversible. I know the front furrow probably has the hardest jobs of all the legs.
Can may one tell me why it's wearing like this? Or did anyone have anything similar.
So. I replaced the seats and pin on the bottom but the bar won't pull into it correctly as seen...
Have an 1998 mf 860 backhoe here. There is a slight bit of wear in the casting for the slew from side to side.
There isn't anyone local who does line boring. Would expander pins do the job? I'd say there is about 2 to 3mm play in the casting.
If it would do the machine another 2000 hrs it's...
With the last few months my water pressure has been decreasing. I have my own well by the house which also does the yard. The yard is about 300 yards from the house and is uphill. So basically the pump has to pump the water uphill.
I have super pressure at the house. Then the further up the...
Hi anyone here running a hitachi digger with a 4 cylinder isuzu engine? I have an ex120 but others might be similar? I need a picture of a piece if anyone has.
What's considered enough wear in a pin to go for a new pin. I'm currently redoing a loader. I have some pins that have 1mm to 1.5mm wear. Does a lad renew these or just reuse them. Doing nothing to them.
I have an old Hitachi ex100 digger here not used much. It has an Isuzu 4db1 turbo engine in it. It has an oil leak that I'm trying to diagnose. Its dripping oil at about a drop per 5 seconds.
Its either coming out the sump gasket at the back of the engine or at the bottom of the timing cover...
Have implements here with the euro Volvo industrial loader brackets etc from an old Volvo 4300 that used to be on the farm. There's a set of pallet forks and bucket etc.
Half interested in this cheap loading shovel as it would be handy and cable enough to lift things around. Scrapped cars and...
Recently bought a caterpillar loader on 500 70 r24 tyres. There a nice wide tyre. Will I still need duals with this size on it in a silage clamp or will a 500 be wide enough?
Do other lads run duals or not with this size tyre?
Going to change torque oil in a cat 910 loader. How much roughly atf oil do these old industrial shovels take? Not sure if I need to buy 1, 2 or 3 20 litre drums of atf. I have the filter bought but unsure on the quantity of oil I will need.
Need to buy on 4 of these tyres on an industrial loader. There working out expensive enough as tyres have gone so dear.
My main priorities is that I have the same height as this tyre and also to fit the rim. I don't need it as wide as 500. Is there anything on an 85 tyre that might work out...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.