Search results

Is it possible to have Agopengps steer JD autotrac machines? (R series specifically) Its all plumbed up as using the SF3000 on SF1 already. Have been looking at agra gps etc but wondered if there was a way to control auto steer using the existing system?

Hi Bart, Which cable do you have for the 250? Basic? or All port? I checked the cabling guide (https://modernaginc.com/wp-content/uploads/2016/11/ez-guide250_cablingguide.pdf) and you are correct about pin 4 and 8. However I read that if you have the all port cable, they want you to use...

Hi everyone, recently acquired a 50B digger instant reverse model. I think it must be the newer version (MKII?) as it has the 2 sticks for the back hoe, instead of the 7. Have given it a full service but having problems with the back hoe. It will raise and lower fine, and dipper stick along with...

Hi all, I am an employee running own Trimble equipment (FM750/CFX 750 with ez steer), a tractor swap happening soon as a new one is arriving. The tractor I am changing over to is Autotrac enabled, however the dome (Starfire 3000) and activations are being ported over to the new tractor, I am...

I had to do a firmware upgrade on my 500 due to EGNOS broadcast change, think it was last year (maybe year before). I'm presuming you have done this on your 250 as you said you have used it last Sept. https://www.soilessentials.com/2019/02/28/egnos-broadcast-update/ Once had to do a hard reset...

Hi all, wondering if anyone has suggestions on this. We replaced the nylon wear ring that sits below the vertical mixing auger and its lasted no time at all. It gets plenty grease pumped in but seems to have melted the plastic. All the bits have went down next to bearing. Whats best when...

Last night we had a Mitsubishi L200 stolen from the Brechin,angus area. Black, single cab 4work edition, not in very good condition. Reg HJ04 UON

Edit: *I have now found a job, can a mod please delete this thread?* Thanks

Just popping in to say thanks for all the replies! They really helped with the fertilizer section. Found it quite difficult trying to work out the timings, especially with it being an imaginary crop. I made sure to mention this thread in my references ;) Cheers.

Hi all, I have a piece of work to do for my college course, establishing a crop in a chosen field. Not looking for the answer but just need a few pointers as its the weekend and can't contact my tutor. Basically, i'm establishing Winter OSR. I have my P + K status, mod - high , mod - low...

Thanks for replies. I fired off an email to BvL who got back to me with a pdf manual and gearbox servicing instructions. This is what we ended up doing, there was a stopper on the upper pipe and a reservoir attached to the other. It was slow going but it eventually filled the box. BvL manual...

Hi all, thanks for the replies. Stripped the gearbox down and pulled the bearings. Gave Sellars and call and was told that 80/90 should be used. Now just a case of building it all back up again. I did spot a tank on the front of the machine with sight glasses. There is a separate hose with a...

Having to replace the top gearbox bearing on our feedcart. Wondered if anyone knew the quantity of oil and grade? Didnt want to stick in 80/90 incase its too thin. Gearbox is a Brevini ec2150/fe. Feedcart is a BvL vmix10. Dropped the gearbox out so its probably best to change the oil whilst...

I did have a think about this some time ago. I had a look about and found that FarmWorks is capable of this. As I don't have a copy of FarmWorks I never did get to try it out. Maybe this will help. http://www.farmworks.com/files/faqs/Office/Site/Guidance_Line_Management.pdf Someone with...

You are spot on about the VAT. Not out looking for a profit, just need these things shifted as they are sitting here in boxes doing nothing. I even had a think about depreciation rates etc before listing the units. Total cost for FM750 was £2,250.00 Free Shipping:£0.00 VAT (20%):£450.00 = £2700...

Have sent you a pm.

Not yet sadly. It is listed on gumtree and ebay but have been told its too expensive, so im open to offers.

Hi all, Sorry for the late reply. Haven't had a chance to get onto the forum past few days. Sorry to those who have pm'd me and no reply back. I will start working through these. Still in the process of boxing up the rest of the GPS equipment but I did manage to box the 750 today so it's ready...

Hi all, I am looking to sell my GPS equipment, long story short I was an employee on a farm and purchased all of my own equipment. Thinking about going to uni/ doing something different so looking to sell everything really.. What happens with the Rangepoint RTX subscription that I purchased...

Hi all, Recently upgraded from an EZ Guide 500 to an FM750. Had an EZ Steer 500 system in place and using this with the 500 screen. Didn't check the cabling guide before hand :rolleyes: and just presumed it would plug into the new 750's cables as the connectors look the same. Checked the...