Search results

Got a mate wants half a tonne for his sheep. What should I charge him?

Drilled some grass yesterday with the combi. Bit late I know. Always flat roll, but a bit worried with possible heavy rain forecast. Slight slope, some clay parts. Do I flat roll before the rain? Cambridge? Or leave? People's thoughts please?

Hi. Wanting a top sieve for a Dominator 58 if anyone knows of anything or possible contact. TIA.

Would anyone know of, or have a baler breaking. Needing a roller for the tension arm. More specifically, the cast bearing holder, so wouldn't matter if the bearings were shot. Tia.

Got the wheel stalk to drop out on this rotor off a JF Z665 Hydro as I need to cut a new circlip groove to hold the bearing in, and could do with the top casting on its own to get in the machine.. Anyone any idea as to how these come apart?

4 of the above required, close to NE Derbyshire as possible. Don't have to be perfect/new, but good enough for occasional road use. Old Verdestein side walls giving way after 30 odd years. Either tyre or on rim. Must be a few lying around as out of favour currently. Please PM if you can be of...

Looking for an 8ft set of chain harrows. Nothing fancy, as long as it'll do a job, but not warn out obviously. To go in front linkage, while I pull roller behind. As close to NE Derbyshire if possible...

Looking for an 8ft set of chain harrows. Nothing fancy, as long as it'll do a job, but not warn out obviously. To go in front linkage, while I pull roller behind. As close to NE Derbyshire if possible...

Wanting to get couple of new 'Fella' stickers for my Fella take I've just resprayed. £25 for genuine ones! Sure I can find someone that would print them cheaper. Anyone have any recommendations? TIA.

Friend has a Fendt 714 to sell. 2 owner, 13000 hours, 2001. Absolutely immaculate, never a problem. Still in original half worn tyres. Arable work only. Would anyone have a rough idea of value for private sale?

As above, have one with a tube in that keeps getting nipped. The rim's been welded in the past, hence the tube. Think it might be easier/cheaper to get a replacement rim and go tubeless again. Anyone know of or have one as in he pic below, 15 x 38? Tidy but not ££££. As near to Derbyshire was...

Firstly, can anyone identify the type/make of packer or scraper this might be? I acquired it several years ago, and replaced the crumbler on my power harrow, but never knew what it came off. The scrapers are fairly basic, work at 90° and used to work ok, but are now worn and don't do a very good...

As per title, dug this up as I was setting a mole trap by the headland in a grass field...

Muck grab to get from Carmarthen, South Wales SA32 to Matlock, Derbyshire DE4 if anyone heading to/from that neck if the woods. Thanks.

Looking for recommendations for an insurance company for a neighbours new (to them) Matbro 250. First machine, so won't be a 'fleet' right now. Won't use nfu. TIA

Hi peeps. Not knowing much about these, anyone hazard a guess as to the value of the above model? 57 plate, 525 hours. Touch if rust on cab pillar, nothing much, just the sh1te water based paint . TIA

Looking for a moisture meter. Doesn't have to be anything fancy. To replace the one I just ran over!:banghead: Which was a protimeter with the grinder and separate compressor and analogue display. Anything considered as long as it works, and not too expensive. Located Derbyshire, so not too far...

Best supplier to obtain boom control valve for an old Hectacre/Allman sprayer? TIA.

As per thread title. Please PM if a possibility. TIA

Looking to move a load of straw as above. Wagon and drag preferred, but could accommodate artic. Please PM if able to help. Thanks.