Trying to get heifer slurry to a lagoon 220m away with 11' of fall. On with constructing a conc 6000 gallon tank to scrape into. This is 5' deep. Thinking of a pipe out of centre of floor which will drop 6' over 20' length then the rest will run level.? Will this work??
03 reg hilux always been flat as a witches tit, put up with it for 3 yr... Do I bite the bullet, add 5k and go newer for an extra 60bhp instantly or tweak what I've already got and is pre dented to match my work style...
As the title suggests , I've a matbro bray telestar 2524 that's started not wanting to go forwards, reversing for a while then changing direction helps, oil levels seem clean and fine but problem getting worse. It's my fault for threatening to change the old girl, any ideas on what to investigate?
I've a 18t plated 28ft drawbar trailer (ex wagon and drag) I'm tweaking into a hydraulic beaver tailed low loader for behind my unimog. It's on twin 19.5 tyres and airbags with fairly central axles so rides well but draw bar is wagon spec so lowest point of trailer then rises to hitch, I'm re...
Have a John Deere 6115m with 3 spools. One tied up with hydraulic compressor, one rotates the rain gun. I've 2 hydraulic single acting gate valves to operate too. I have both plugged into remaining spool and just pull lever either way depending which I want to use, then put into float to close...
Just cut all the steel to drawbar a 45ft tri axle artic flat trailer for a neighbour to draw straw in with, I told him to try a dolly but insistent on a drawbar. Looks like he'll need shares in gate posts the way it will it corners!
Has anyone already done one? What's the longest drawbar you...
9ft cut, 3 rotor. Pto drives a 90* degree gearbox onto the first of 3 pulleys. First pulley (approx 300mm diameter with 2 v's is fudged)
Thought to bea Wylie , after confirmation and a source for a new pulley
Stripped the pump down on my 2002 takeuch tb53fr (possibly same as other models)
Its a Uchida pump and my problem lies in the gear section.. (piston and pilot pump seem fine)
ive contacted local dealers last week who are dragging their feet... after ringing some independants tomorrow...
any...
As the title suggests I'm after a v belt pulley that will ideally fit direct onto a 6 spline male pto shaft.
I've a drain jetter that I rarely use below 1000rpm. Meaning unimog revving its cock off supping diesel when there's no need. I have an input shaft with pillow block bearings and a large...
Has anyone on here roofed over a clay bank lagoon or even dug a clay lagoon inside an existing building? After 300,000g of the cheapest storage possible . Requirements are...
No rainwater, access to empty sediment. Flexibility should my job alter.
As the title suggests I'm after running an 1100mm wide chassis between the spring hangers/ or airbags whilst running mini super singles.. Is it possible?
My matbro has eaten it's combined rad/oil cooler due to a rawl bolt in the floor![emoji26]
Who's the best source for a new one or re coring this one (Preston lancs)
Tia rob... One for @ACEngineering?
Been given this by a mate....
Wanting to hook into electrics and have warm water for hand wash , always run with the lights on as it's always stupid o clock so wondering if I could power it off the light circuit or will I have to draw power from in cab plug to a relay activated by the light...
Under the pre tense of looking for shooting a silver land rover discovery comes into the yard and has a good scout around. No more details sorry but so far they've had...
Land rover td5
Honda foreman 400 (12month old damage to front rack)
Power washer
And several cars and power tools..
Attempted...
Has anyone on here encountered ecu problems. Specifically tb 53fr. After an extensive steaming to locate a burst hydraulic pipe the digger has a mind of its own. Auto idling and peckering at random. Anyone encountered similar? Ecu set into chassis with all drains blocked after having it cab...
I've a 165ft feed passage to create using 4" concrete panels. 15' long 2' high (raising the feed level 6") The passage will be cleaned out with loader and automatic scrapers running down the other side. What's the tightest fitting rsj for scrapers/ bucket to run past? Or has anyone used 4" thick...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.