These seem to be getting more popular.
How are people getting on with them?
Few Questions:
Can a remote engagement switch be easily connected, I realise there is the button on side of motor and on screen.
Can you with these or any other electric steering wheel type system - disengage by grabbing...
Hi All
Thought I'd start a new thread as the old one's getting a bit long.
Transmission fluid level - According to book - Run at idle for 2 minutes turn off wait 2 minutes then check.
I take from this the ideal level would be on (usually would go just above) the upper mark where it says hot...
We bought one back in April but only starting to use it more now as it's spring.
I've set the hydraulic spools on the black joystick buttons, top one for float, bottom one for raise (+). Set the flow for the job and timer 3 to 4 seconds. Use for the baler pickup and tried it on the front and...
Hi
We have a 2006 J D 6420 Premium Common Rail, the water to air intercooler that sits on top of the inlet manifold - looks like a stack of rectangle plates, part # AL 172 218 has always leaked coolant a little bit at the base, has got abit worse - can these be repaired or is replacement the...
On the Joystick's black buttons which can be programed for various functions, can you put Hyd. spool extend on the rear and FLOAT on the front button for say baler pickups mowers etc (we have Fendts)?
CTV Trans Control: In Manual mode - using joystick to speed up slow down, then set Rev hold...
Hi All,
We have a Krone BP890 XC HS.
This has the pretty basic double knotters. The bill hooks and some of the other parts are the same as a CNH LBX332 we used to have.
We can get it running pretty good on silage - if the twine holders are too loose and bill hook tension too tight it will hang...
Hi these are a friend's tractors (I have Fendt's:)....... + 1 JD)
First 1; 2004 6820 Basic tractor non common rail eng. but with electronic controled pump, intermittent no start more so when hot, ECU was replaced as per codes about 4 years ago, cured problem at the time.
Problem has reocurred...
Looking for a new 3m (10ft) mower conditioner.
Looking at the Krone EasyCut R320 CV.
Anybody got one or what do you think?
Sometimes we mow in conjunction with a front mower, sometimes not.
A bit of a drawback would not being able to quickly adjust the offset of the mower (change balls to pins...
We've got a 574 we've had from brand new + a 585 we acquired recently they are now mainly just yard tractors, use 574 for feeding out (light)
Was having trouble bleeding up brakes + getting to stay up on the 585, was ready to accept the brake piston o-rings were gone.
Thought better check the...
Just thought I would post up a problem and solution we had last season with our 818, might help somebody else.
It had slow starting response on the auxillary hydraulics when under heavy load, i.e. lifting twin rotor rake at headlands. It didn't matter where the flow control was set. It didn't...
I had posted this on another forum but since I've joined here I thought I would transfer it here too.
I got 2 sets of these to try https://www.larsenlights.com/par-36-hi-lo for our IH 574 + 585 hope they last alot better than the crap 45/45 watt sealed beams.
Also got a flood one to try, which...
I had posted this on another forum but because I've joined here thought I would transfer it here too.
Had a go at doing our 574 handbrake through the side. Read up what I could find on the net, so thought I would do some notes for next time and maybe help someone else.
Quite a bit of what I...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.