quicke

Looking for one in the 2 _3k bracket , unheard of make, maybe,Strimech have outpriced themselves, they are over 5k now, considering there paint job on my grain bucket is as thin as fag paper. What are we paying for here, steel has come back. Cherry x around 4k still to much imo.

Anybody tried or bought one What's the verdict? TIA

Hi Folks. Anyone know if theres a place where i can get a replacement barrel for a hydraulic ram off my ALo SG200 shear grab. Ram / pipe fitting got damaged and then repaired badly.. ram now duff..

Looking for set of brackets to fit a quicke Q40 Thanks

Help. Oil squirting from "valve" on one arm (see photos). What is it / what's it for? Fix? Thanks

Got a Quicke Q56 loader on a 2013 MF 5470, came new together but I didn't drive much initially to know if it was ever any better than it is now. It seems gutless whether lifting or crowding, if you overload it, it just sits there doesn't even seem to take any weight at all off of the back...

Just picked up a CS110, MX/Chillton loader, however have access to euro 8 attachments. Can anyone point me in the right direction for a headstock conversion. Can’t seem to find one that fits. It’s a lot of effort sending these units back 🤣🤣🤣

Got a quicke loader mf 4327 6m? Equivalent Hydraulic locking is messing about. If I press and hold 3rd and 4th buttons and move lever it tries to unlock but only moves a little. If I put the softride plug into hyd locking solenoid it works ok IE flinch switch press 3rd move joystick moves in...

I’m really struggling to connect the hydraulics on my Valtra loader, can’t get a he two halves to come together. I have tried a bit of grease for lubrication. At what point does the locking handle come across, do the two halves have to be fully together first or does the handle pull them...

any body know where we can get quickie loader accumlators from or even the same spec as originals, original part number is alo 5045140

Lets take 50mm pins and bushings. If your pin was measuring 49.5mm or 49mm would you keep of dump it? Just wondering how much wear is too much wear. Similar with a bushing.

As the title suggests, I’m after a foot throttle conversion for an MF 65. Does such a thing exist, and if so, where can I purchase one from.

Hi All, please does anyone have a stand for a 1980’s Quicke loader in the back of a shed? We have inherited a loader which came without one. It makes supporting the loader when not in use and reversing the tractor out of it. The part number was 1 32 180. See attached picture. Fingers crossed. Thanks

Anybody got any drawings with measurements for jcb q-fit making a quick attach headstock to fit on my uncles jcb 3cx want to make it as close to factory dimensions as possible. Thanks

Underhaug KV Bale Spike, Bale Grab needs some tlc comes as seen in photos no pipes included. Quicke No.3 brackets Collection from Welford Northamptonshire or could possibly deliver £250

Anybody use the iae barley beef feeder it says 1000lter capacity would that hold a ton of cake/ finishing blend thanks

Bit of a problem to solve… The levers on our 574 loader have both broken off the mounting plate. We’ve hobbled along with the help of some cable ties but it’s now fairly unusable i thought it would be easy enough to swap for new levers and maybe matching cables, but it appears to be more...

Will be putting in 4 feed pads roughly 12 x 30m this spring ready for next winter. They will be gravel finished ontop of fairly lumpy rock the bring, crap to spread and push around but awesome base for fine gravel. These will be fenced so room will be a bit tight and really only have the 140hp...

claas 2019 630 cebis 3000 hrs front linkage 50 k led lights full gps tyres 75% quicke q6m loader warranty and gps subscription to 5000 hrs or june 2026 local farm is looking to sell this

What do people prefer. Over the top Soft grab Dual purpose bars/spikes