A few workshop jobs.

[Willie adie]

Nice thinking and making there.
I'm rough. I just use a pointed lump of 16mm round bar and the hammer.

My blacksmith friend made it I just told him what it was for

 

[Larel]

I went for ram mounts. Bolted one to the back of the box and another clamped to the rail. Will give me flexibility just now till I get everything mounted.

 

[TripleSix]

Gearbox died on the Milwaukee grease gun, it's had a lot of work and some abuse.

Still nearly £200 for a new gun, a new gearbox was purchased for £52 delivered.

20 minute job to swap it

Just in case you wondered what was in there, about 4 sets of planetries!

 

[tomlad]

strategically place milwaukee screw driver

 

[Oldmacdonald]

I went for ram mounts. Bolted one to the back of the box and another clamped to the rail. Will give me flexibility just now till I get everything mounted.
View attachment 1126299View attachment 1126300

Jesus christ, what is that the control box for??!

 

[Neil MP]

Jesus christ, what is that the control box for??!

A Claas round baler,

 

[shumungus]

Gearbox died on the Milwaukee grease gun, it's had a lot of work and some abuse.

Still nearly £200 for a new gun, a new gearbox was purchased for £52 delivered.

20 minute job to swap it

View attachment 1128721

View attachment 1128722

Just in case you wondered what was in there, about 4 sets of planetries!

View attachment 1128723

View attachment 1128724

Where did you buy the gearbox?

 

[fermerboy]

Where did you buy the gearbox?

I got a new one here
https://www.ebay.co.uk/itm/274517847728
Good as new again.

 

[shumungus]

I got a new one here
https://www.ebay.co.uk/itm/274517847728
Good as new again.

They are the repair/warranty agents for Northern Ireland.

 

[TripleSix]

Where did you buy the gearbox?

MILWAUKEE M18GG CORDLESS GREASE GUN - REPLACEMENT GEARBOX ASSEMBLY | eBay

MILWAUKEE M18GG CORDLESS GREASE GUN - REPLACEMENT GEARBOX ASSEMBLY

www.ebay.co.uk

 

[Larel]

My SDS drill burnt out last week. Running about half speed and sparking badly.

 

[Larel]

Spares from here arrived 3 days later and all back together good as new.

 

[Larel]

Spent a few hours making a kart for the kids to run in a race at the weekend. Not sure it will make it to the bottom of the hill but they are happy so far!

 

[colhonk]

Hope you have got the Ackerman angle right

 

[Scrapjockey]

That could be the best paying job ever, definitely be remembered in years to come.

 

[Larel]

Hope you have got the Ackerman angle right

Just a guess at the angle required. No sums or angle measurements were harmed during this design and build!

 

[Larel]

That could be the best paying job ever, definitely be remembered in years to come.

Wise words!

 

[Larel]

While testing my AOG build winter project I mixed up some wiring and software settings and dead headed the steering pump on my NH 5635. Lost all pressure and had to drive home with no PS and tired arms.
I took the pump off and found a sheared woodruff key in the coupling.

 

[Larel]

I stripped the relief valve as well, to make sure it wasn’t sticking. Nothing obvious so all back together with a new key and it’s steering once again. I took home a spare key just in case……….!

 

[Zebbedee]

I stripped the relief valve as well, to make sure it wasn’t sticking. Nothing obvious so all back together with a new key and it’s steering once again. I took home a spare key just in case……….!

View attachment 1167412View attachment 1167413View attachment 1167414View attachment 1167415View attachment 1167416

That was very lucky then