AgOpenGPS RTK Autosteer, How to Guide for £1000

[andyinv]

Woosh straight over

Hmm. Maybe I'll do a video guide. Are you using rtkbase ?

 

[davidroberts30]

Hmm. Maybe I'll do a video guide. Are you using rtkbase ?

Ive signed up will try entering my base on it later

 

[davidroberts30]

Yup, you can do that. Ntrip A and B in rtkbase. Also, with AOG, you can run tailscale on rtkbase and your tablet and connect direct to home securely

Im guessing thats some way to connect base to tractor directly without using a 3rd party castor?
I dont mind broadcasting on the likes of rtk2go
I just want no issues when im out in the field

 

[andyinv]

Ye

Im guessing thats some way to connect base to tractor directly without using a 3rd party castor?
I dont mind broadcasting on the likes of rtk2go
I just want no issues when im out in the field

Yeah it goes direct - you can still send to centipede/rtk2go as well, it just gives you that ability to bypass them.

 

[davidroberts30]

Ye

Yeah it goes direct - you can still send to centipede/rtk2go as well, it just gives you that ability to bypass them.

can the base be set up to send to more than 1?? This is my current output

 

[andyinv]

can the base be set up to send to more than 1?? This is my current output

rtkbase can send to 3 - two NTRIP online, and one local.

 

[Will Blackburn]

We are on Emlid as well as rtk2go

 

[Nigley]

Needing help again, I have it setup now in tractor and whenever I open the configuration menu I get this and I can get through the left hand tabs but can’t save anything or get out of it, only way I can get out of this is to force a shut down of whole tablet. Any ideas? Thanks in advance

 

[Spear]

You’re missing the bottom of the box, it’s off the screen. Try moving it or adjusting screen resolution to see all of it

 

[Nigley]

You’re missing the bottom of the box, it’s off the screen. Try moving it or adjusting screen resolution to see all of it

Yes just realised that just changed resolution and sorted it thanks

 

[hollister]

Last few times I started agopen after 30 seconds Agio just seemed to become unresponsive and had to shut down agopen and restart.

The above sometime repeat upon restart.

It will start and work as normal but often after 3 attempts

Any ideas ?

I get agio crashing and having to reopen it but agopen keeps running

 

[YoungFarmer23]

Hi, I’m a bit stuck at the moment with my wheel angle sensor(discovery 2 sensor), I’m try to mount it on a John Deere 6430 premium but I’m having trouble trying to find a suitable position for it. I’m now starting to think if it would be easier to buy the factor angle sensor and put that in as they’re only £30. I was just wondering if anyones done it before? and how difficult it would be to add it to the axle and wire it into the system?

Thank you

 

[aidan]

I get agio crashing and having to reopen it but agopen keeps running

same error i think

how do you recover, close agopen and restart ? thats what i have been doing

 

[hollister]

Just pressing agio, it opens again, maybe have to do it two or three times and it stays running

 

[BuskhillFarm]

Hi, I’m a bit stuck at the moment with my wheel angle sensor(discovery 2 sensor), I’m try to mount it on a John Deere 6430 premium but I’m having trouble trying to find a suitable position for it. I’m now starting to think if it would be easier to buy the factor angle sensor and put that in as they’re only £30. I was just wondering if anyones done it before? and how difficult it would be to add it to the axle and wire it into the system?

Thank you

Is that any help? Not sure if 6430 has those wee threaded holes but I made a bracket up and screwed in there

 

[KennyO]

Sorry a few questions. Could I set up AgOpen GPS to give me a speed signal for a fert spreader or sprayer. I would quite like to occasionally use the sprayer on our NH TM which has no readout plug in the cab.

Also if I was to go down the steering route with the TM could I tap into the steering angle sensor which is fitted for the auto 4wd/diff lock disengage?

Thanks

 

[S.Jamieson]

Sorry a few questions. Could I set up AgOpen GPS to give me a speed signal for a fert spreader or sprayer. I would quite like to occasionally use the sprayer on our NH TM which has no readout plug in the cab.

Also if I was to go down the steering route with the TM could I tap into the steering angle sensor which is fitted for the auto 4wd/diff lock disengage?

Thanks

Yes

Don't know.

 

[andyinv]

JCB 4220, steer-ready, 2022 model.

 

[davidroberts30]

Ive signed up will try entering my base on it later

Finally got it connected this morning with help from @andyinv
Been fault free all day

 

[young bull]

Hi, I’m a bit stuck at the moment with my wheel angle sensor(discovery 2 sensor), I’m try to mount it on a John Deere 6430 premium but I’m having trouble trying to find a suitable position for it. I’m now starting to think if it would be easier to buy the factor angle sensor and put that in as they’re only £30. I was just wondering if anyones done it before? and how difficult it would be to add it to the axle and wire it into the system?

Thank you

On our 7530 there’s a threaded hole on the back of the axel we’ve used to bolt the plate on needs a bit of fine tuning and trimming.