AgOpenGPS RTK Autosteer, How to Guide for £1000

[Toki]

Finally work

 

[Tim G]

I've got all the software up and running and have an RTK signal now just waiting for the Baraki valve to arrive.

Has anybody got any recommendations for a neat switch to turn on the guidance? Looking for one to fit where the front PTO would go on a JD 7530. I'm thinking it wants to be a normally open momentary switch?

I had nowhere particularly nice or convenient and I didn't want to drill holes. I think a foot switch would be better and I might add one but in the meantime I used a small enclosure and some strong sticky hook and loop tape.

 

[andyinv]

I had nowhere particularly nice or convenient and I didn't want to drill holes. I think a foot switch would be better and I might add one but in the meantime I used a small enclosure and some strong sticky hook and loop tape. View attachment 1179768

Could have used the factory engage button on the panel ?

 

[Tim G]

Could have used the factory engage button on the panel ?

Yes, that would be a good solution but I don't have the knowledge how to go about that just yet.

 

[Toki]

хттпс://иоутубе.цом/схортс/ОЕтзСгАХ2нК?си=о6ДпПЕвММХ9анф7р

 

[andyinv]

Yes, that would be a good solution but I don't have the knowledge how to go about that just yet.

I'll ping you a firmware for it later - CANBUS for the panel is on the rear pillar.

 

[Toki]

 

[Toki]

How to delete this field?

 

[andyinv]

How to delete this field?

From Load page

 

[e3120]

How to delete this field?

Or in windows explorer. Delete the folder or move somewhere for safekeeping to de-clutter AOG.

It would be nice if AOG could handle field subfolders.

 

[Toki]

W

From Load page

Where is that?

 

[Tim G]

I'll ping you a firmware for it later - CANBUS for the panel is on the rear pillar.

Thank you. I'm already plugged into the canbus so is it just an update/upload of the firmware that I need to do?

 

[Andy26]

Thank you. I'm already plugged into the canbus so is it just an update/upload of the firmware that I need to do?

Have you got two plugs?

 

[Tim G]

Have you got two plugs?

Yes, black and green and I'm plugged into both.

 

[andyinv]

Yes, black and green and I'm plugged into both.

Which board do you have? And what tractor/age?

 

[Tim G]

Which board do you have? And what tractor/age?

I think it's a V2.5 board, 2018 case maxxum tractor.

 

[Lewis]

Probably been asked before but What off-set should I put in for front and back mowers? 3meter front and backs.
Thanks

 

[davidroberts30]

Probably been asked before but What off-set should I put in for front and back mowers? 3meter front and backs.
Thanks

Dont start about mowersset mine up measured everything
Completly wrongtried everything i could think of
Back to last years way of a 146cm offset on the antenna

 

[Northern farmer]

Probably been asked before but What off-set should I put in for front and back mowers? 3meter front and backs.
Thanks

In the early days AOG had problems with large implement offsets like one half of the implement width or so. Should be fine now.

Assuming you do not have any overlap between the front and the rear mover, your offset should be 1.5 metres. It is a 6 m implement and the tractor drives 1.5 metres from the centre line.

I would need to test if the offset is to the left or right, my brains never work it out however clear the instructions are.

 

[Will Blackburn]

Probably been asked before but What off-set should I put in for front and back mowers? 3meter front and backs.
Thanks

Offset 143cm right, 586cm machine width then 10 to 15 cm overlap. Tape measure to confirm when mounted, mostly for the front/back overlap.

We've got triples this year with an adjustable rear mower width, no offset but plenty to cause mither, though about programming two machine sets or change the overlap on the go?