Amazone Gps switch whit John Deere no Gps

[jd4055]

Cant get my Gps switch to conekt to the starfier 3000 got the cabel from John Deere PF 90350 but switch say no Gps what to do? Help

 

[Northern farmer]

1) did you set the baud rate correctly for the NMEA output from your Starfire (19200)?
2) did you configure the starfire NMEA messages correctly (GPGGA, GPVTG, GPGSA)?
3) are the rx and tx pins on the RS232 connector matching the rx (and tx) pins at the GPS Switch connector?

 

[super4]

I know its not the same, but run my amatron3 box with a starfire 3000 reciever .I can only get the gps to work if I have the 2600 screen plugged in and powered up.

 

[jd4055]

Northen Farmer
Nr 1 yes 19200
Nr2 yes
Nr3 dont know what you mean
I upploded some pictures on cabel if that help

Super 4 I Will try to disconnect the 2630 and se what happens

 

[jd4055]

1) did you set the baud rate correctly for the NMEA output from your Starfire (19200)?
2) did you configure the starfire NMEA messages correctly (GPGGA, GPVTG, GPGSA)?
3) are the rx and tx pins on the RS232 connector matching the rx (and tx) pins at the GPS Switch connector?

Nr 1 yes
Nr 2 yes
Nr 3 dont know what you mean

 

[Lofty]

3) are the rx and tx pins on the RS232 connector matching the rx (and tx) pins at the GPS Switch connector?

If thats a new NMEA lead from JD, i'd speak to your dealer. Mine wouldn't work when new and the dealer swapped the wires around in the plugs but that was 4 years ago.

 

[Northern farmer]

If thats a new NMEA lead from JD, i'd speak to your dealer. Mine wouldn't work when new and the dealer swapped the wires around in the plugs but that was 4 years ago.

Was it pins 2 and 3 on the RS232 connector? There are adapters and wires that do this, one should just figure out first the correct order. It should be pin #2 on the GPS Switch connector that receives NMEA data. jd4055 should check if the JD lead has transmit data on pin #2. Can be measured with a multimeter if needed.

 

[Lofty]

Was it pins 2 and 3 on the RS232 connector? There are adapters and wires that do this, one should just figure out first the correct order. It should be pin #2 on the GPS Switch connector that receives NMEA data. jd4055 should check if the JD lead has transmit data on pin #2. Can be measured with a multimeter if needed.

No, it was the male and female connectors between the receiver and the plug on the front of the cab.
Thinking on, it might have been something to do with the power. Are we sure the reciever is powered and working on the 2630 with the NMEA lead connected?

 

[peterH]

Are you plugged into the correct port on your screen?

 

[Lofty]

Are you plugged into the correct port on your screen?

Second question to the OP and no answers. Does annoy me when someone asks for help, gets lots of it and then never bothers to tell everyone if they have sorted the issue and what the problem was. Thought the idea behind a forum like this was that it helped others as well as yourself.

 

[Pheasant Surprise]

Second question to the OP and no answers. Does annoy me when someone asks for help, gets lots of it and then never bothers to tell everyone if they have sorted the issue and what the problem was. Thought the idea behind a forum like this was that it helped others as well as yourself.

To be fair it’s mostly the blow ins that do that.

 

[Lofty]

To be fair it’s mostly the blow ins that do that.

'Blow ins'... new phrase on me... like leaves under the door you mean?

 

[Pheasant Surprise]

'Blow ins'... new phrase on me... like leaves under the door you mean?

In the vernacular....

https://www.macmillandictionary.com/dictionary/british/blow-in_2

 

[General-Lee]

Are you plugged into the correct port on your screen?

Doesn’t look right to me, Amatron 3 here though.

 

[Northern farmer]

Doesn’t look right to me, Amatron 3 here though.

On the GPS Switch the GPS receiver is plugged to the connector on the left at the bottom of the screen.

 

[CPP]

Have you sorted it

If not what tractor are you using it on

 

[jd4055]

hello thanks for all ansers finaly got it working needed to move green and gellow cabel from the female conection to the male conection on the cabel that goes to the gps switch on the roof of traktor.... that or by one more cabel,....