case lift arms not working

[y2kf]

case mx 135 lift arms are not working when using the round dial in cab,rocker switch seems too make it raise a small bit and if you keep pressing it it will lower bit by bit,will work perfectly when using the rear fender buttons,also using the the lift settings under the wee flap in the cab it does nothing,any idea's?

 

[rc mx110]

case mx 135 lift arms are not working when using the round dial in cab,rocker switch seems too make it raise a small bit and if you keep pressing it it will lower bit by bit,will work perfectly when using the rear fender buttons,also using the the lift settings under the wee flap in the cab it does nothing,any idea's?

The tiny tiny bulb in the rocker switch to raise lower the arms has blown. Its part of the circuit
Mine did something similar yrs ago.

 

[y2kf]

My bulb is still lit,can other bulbs be the cause,i jus got my alternator fixed,would that of blown something?

 

[rc mx110]

Erm not sure, any numbers flashing on screen below flap?

 

[y2kf]

The letter E.and a dot too.

 

[rc mx110]

E???
I always thought it only displayed 0-9??
Prob best get an expert help @McCman

 

[8100]

http://www.tractorbynet.com/forums/case-ih/312793-mx150-3-point-hitch-arms.html

 

[Chap]

1 of the potentiometers in linkage. Our 110 did the same. Ended up replacing them both, one under round dial in cab and other under triangle cover left of top link

 

[McCman]

Error code E is high battery voltage, greater than 18 volts !

Id get that new alternator / battery's checked out sharpish before it causes any more problems !

could you have fitted a 24volt alternator ?

 

[McCman]

E???
I always thought it only displayed 0-9??
Prob best get an expert help @McCman

The error coded display thingy can show any form of a shape, dot, dash or number for an error code.

It should always show 0. when everything is working ok

 

[y2kf]

Good too see you mccman,was havin trouble with starting this tractor so have two batterys connected together and earthed too a stud under engine,got starter cheaked,new contacts put in,new starter relay,found that alternator was draining me batterys so sent it too get sorted,put new ring in it or something,put all together,loads of power now starting straight away,realy bright lights in dash,then i noticed the lift arms not working,started it many times today,blew the head lights bulbs but i think they where faulty anyway,went out there too start it again,no joy dash lights still very bright but jus clicking fast at starter,did turn the engine but very weak,is the alternater sill draining the batts or whats going on?

 

[ridger]

What way did you wire the battery's togethrr have you made them 24 volt

 

[rc mx110]

What way did you wire the battery's togethrr have you made them 24 volt

should be + to + and - to -

 

[y2kf]

Yes you's where spot on i had them wired for 24 volt,sorted now but time will tell if my batteries are still been drained,would a 650ah battery be enough on its own too start it?When i started it this evening lift arms still didnt work,after a while there was a slight buzzing noise behind the spools somewhere so i jiggled the wires in and around there and noticed the rocker switch light went out and the lift arms are working again strange but i heard that noise before.

 

[reno110.54]

The error coded display thingy can show any form of a shape, dot, dash or number for an error code.

It should always show 0. when everything is working ok

what does number 4 mean under the flap?

 

[gmc541]

what does number 4 mean under the flap?

I would like to know to answer to the no. 4 also

 

[asm]

Number 4 is the bulb has failed in the fast raise rocker switch

 

[gmc541]

Thank you very much, I bought one today and no4 is on screen.

 

[MAMC]

What does a dash mean on the display under the flap? Looked at one and it had that display.

 

[Lincsman]

I am surprised anything works again after running at 24 v, but guessing it would be 20V max as you cannot charge at 24V