ERRORE E 24 FORD 8240

[Riccardo]

Salve a tutti. Possiedo un FORD 8240 che da qualche tempo segnala il codice di ERRORE E24, ma comunque funzionava. Da poco, mentre ero in marcia col trattore, cambiando la leva delle marce da ridotta a veloce, si è fermato. Dal giorno non riesco più a farlo funzionare. Sapete dirmi di cosa si potrebbe trattare? E' possibile inoltre avere una copia del manuale dei codici di errore?
Grazie.

 

[Goweresque]

Translation:

Hello everyone. I own a FORD 8240 that for some time has been reporting the ERROR code E24, but still worked. Recently, while I was driving with the tractor, changing the gear lever from reduced to fast, it stopped. From the day I can no longer make it work. Can you tell me what it could be? Is it also possible to have a copy of the error code manual?

 

[kitigwa]

Translation:

Hello everyone. I own a FORD 8240 that for some time has been reporting the ERROR code E24, but still worked. Recently, while I was driving with the tractor, changing the gear lever from reduced to fast, it stopped. From the day I can no longer make it work. Can you tell me what it could be? Is it also possible to have a copy of the error code manual?

hi
i have the same problem with my ford 8240 sle
any help

 

[bobk]

E24 is rear linkage calibration required

As for no drive , check the wires to the levers , quite common for the wires to get crushed .

 

[kitigwa]

wire checked all working
tractor can not move or lift implements

 

[kitigwa]

E24 is rear linkage calibration required

As for no drive , check the wires to the levers , quite common for the wires to get crushed .

wire checked all working
tractor can not move or lift implements

 

[bobk]

wire checked all working
tractor can not move or lift implements

Any error codes

 

[kitigwa]

E24 is rear linkage calibration required

As for no drive , check the wires to the levers , quite common for the wires to get crushed .

tried to calibrate and it gives me u19 and u99 error

 

[kitigwa]

Any error codes

u19 and when calibrating it say u99

 

[bobk]

u19 and when calibrating it say u99

Not familiar with that code , @agrimax @forblue

 

[agrimax]

If it says E24 in the bottom of the middle display,it means ''C3/C4 clutches not calibrated''.
Code 24 in the right hand display means ''perform hydraulic lift calibration''.
U19 does not exist but E19 in the middle display means''dump solenoid open or short circuit or C3/C4 pressure switch open circuit''.
U99 is system failure,probably being displayed because of the faults with E24 and E19.
Check fuse 13. IIRC,my 8240 lost drive and hydraulic lift and it was the big red (might have been orange) relay in the fuse box that had failed.Too long ago to remember if any or what codes were displayed.Could also be corrosion in the multiplugs abive the battery.

 

[kitigwa]

If it says E24 in the bottom of the middle display,it means ''C3/C4 clutches not calibrated''.
Code 24 in the right hand display means ''perform hydraulic lift calibration''.
U19 does not exist but E19 in the middle display means''dump solenoid open or short circuit or C3/C4 pressure switch open circuit''.
U99 is system failure,probably being displayed because of the faults with E24 and E19.
Check fuse 13. IIRC,my 8240 lost drive and hydraulic lift and it was the big red (might have been orange) relay in the fuse box that had failed.Too long ago to remember if any or what codes were displayed.Could also be corrosion in the multiplugs abive the battery.

Yes, it say E24
when i try to calibrate, C3/C4 the number increases up to 50 and then E19 or sometimes E99 appears.
called the electrician and he says every fuse is good and working perfect.
i am confused cause nobody here knows how to fix the problem.
i am trying to fix it myself,
i have a shop manual but not much knowledge.

any advice please