How to set up your own RTK base station.. for about £300

[davidroberts30]

Okay, my ip was 192.168.1.123 and I put that into my computer and it seemed like nothing was happening.

You would have to be on that network?

 

[YoungFarmer23]

You would have to be on that network?

they’re both on the same network

 

[davidroberts30]

they’re both on the same network

On my ntrip wifi master to make any changes i need to disconect from home network and connect to the ntrip network, then access via 192.168.etc

 

[davidroberts30]

Doesnt matter they both connected to home wifi

 

[YoungFarmer23]

Hi again, so I’ve followed all the steps on configuring the pi and I’m now stuck again. I’ve put my ip into my web browser and I get into it okay but it’s showing nothing. I was wondering what I need to do now?

Here’s some screen shots:

 

[YoungFarmer23]

I’ve finally got it sorted! I just started from the beginning and it finally configured the F9P when the raspberry pi booted and it’s now working!

 

[S.Jamieson]

How would I remind myself on my base station name registered on centipede?

I forgot what it was and it's different to what I set up on rtk2go

 

[Topittom]

hi again folks. Just wondering what to put in the mobile network settings section on a 2015 fendt? I got a sim from v12 and have contacted them for advice but they aren’t certain. The details I got from v12 was profile name/APN/username/password. The screen on the tractor is as below. Any help appreciated. Thanks

 

[del_boy]

hi again folks. Just wondering what to put in the mobile network settings section on a 2015 fendt? I got a sim from v12 and have contacted them for advice but they aren’t certain. The details I got from v12 was profile name/APN/username/password. The screen on the tractor is as below. Any help appreciated. Thanks View attachment 1180075

Do you need to fill in every box? Have you tried entering the info you have and tried connecting.
Ive got pictures from our 2013 724 but not of that page , can get them tomorrow
This is what i have on my phone for that page

Just looked again its the wrong page my bad

 

[Topittom]

Do you need to fill in every box? Have you tried entering the info you have and tried connecting.
Ive got pictures from our 2013 724 but not of that page , can get them tomorrow

No I don’t think you need to fill every box, the details from v12 were actually to leave username and password blank but im assuming the profile name or APN I got go in the accesspoint box and leave the rest blank. I’m sure I’ll figure it out, just wondered if anyone knew straight for sure

 

[andyinv]

No I don’t think you need to fill every box, the details from v12 were actually to leave username and password blank but im assuming the profile name or APN I got go in the accesspoint box and leave the rest blank. I’m sure I’ll figure it out, just wondered if anyone knew straight for sure

Profile name, anything you like eg V12. APN is pkp18-inet. Leave the rest blank

 

[S.Jamieson]

How would I remind myself on my base station name registered on centipede?

I forgot what it was and it's different to what I set up on rtk2go

I also didn't write down my base ip address....how do I access rtkbase again?

 

[andyinv]

I also didn't write down my base ip address....how do I access rtkbase again?

try http://basegnss.local

 

[Topittom]

I’ve got my base station setup but running into a few issues. This is the screen I get once logged in etc, accuracy seems to be too high.

and when I try to engage auto steer I get this error message

 

[andyinv]

Tractor GPS too close to trees/buildings perhaps? Should never be anything like that, not once RTK has locked.

 

[Topittom]

Tractor GPS too close to trees/buildings perhaps? Should never be anything like that, not once RTK has locked.

I did take it out into a field so shouldn’t be that. Just ranged from 1.4m-1.9m. scratching my head a bit

 

[andyinv]

I did take it out into a field so shouldn’t be that. Just ranged from 1.4m-1.9m. scratching my head a bit

Aye, I've done loads of Fendt, new and old, with rtkbase, no issue.

 

[Topittom]

Aye, I've done loads of Fendt, new and old, with rtkbase, no issue.

This base was made with WiFi ntrip master so haven’t used rtkbase. I’ll have a play around but not sure where to start. I’ve changed the messages it’s pushing out and that didn’t make any difference

 

[Andy26]

I’ve got my base station setup but running into a few issues. This is the screen I get once logged in etc, accuracy seems to be too high. View attachment 1180714
and when I try to engage auto steer I get this error message
View attachment 1180715

Sure you've got mount name correct. Of course it could be RTK2Go is down, it has been today and quite a bit this last week.

 

[Topittom]

Sure you've got mount name correct. Of course it could be RTK2Go is down, it has been today and quite a bit this last week.

Could be it. I’ll try again next couple of days and see what happens