Hydraulic fittings help needed

[Pembs]

Hi,

Anyone got any idea where we could get hydraulic fittings like shown in the picture?

Ideally, we would like to buy just the crimp on fittings instead of having to buy the whole pipe.

They connect onto the transmission cooler on New Holland TM series ( & 6080 etc.).

 

[joe soapy]

find someone that can weld ally and weld a bit of thread on it

 

[Mursal]

One off repair, or ends needed for a project?

 

[Mur Huwcun]

Is the fitting a once piece or two piece? If two piece split open the ferrule. Carefully cut down both sides with cutting disc, stopping just before the lip, then split with chisel. A big no-no on usual hoses but transmission cooler is on return circuit with reduced pressure anyhow.

 

[Mur Huwcun]

find someone that can weld ally and weld a bit of thread on it

It'll never weld having been exposed to oil, no matter how much you clean and wash it will sweat out a ruin the weld!!!

 

[Mursal]

Aluminum solder might take with a good active flux?

 

[agrimax]

Would be surprised if Pirtek don't have fittings like that.
http://www.pirtek.co.uk/downloads/products/Hose and Fittings.pdf

Likely in there somewhere........

 

[milkloss]

Is the fitting a once piece or two piece? If two piece split open the ferrule. Carefully cut down both sides with cutting disc, stopping just before the lip, then split with chisel. A big no-no on usual hoses but transmission cooler is on return circuit with reduced pressure anyhow.

I'm with this one, just make sure it gets a new o ring too.

 

[Dave W]

A decent hydraulic specialist will be able to identify that.
I had something similar on a quicke loader. Was told dealer only fitting but Derbyshire hoses and fittings got me some next day.

 

[mengeleguru]

We keep the quickie ones but nothing like that.

 

[Pembs]

Is the fitting a once piece or two piece? If two piece split open the ferrule. Carefully cut down both sides with cutting disc, stopping just before the lip, then split with chisel. A big no-no on usual hoses but transmission cooler is on return circuit with reduced pressure anyhow.

Unfortunately the fitting in the photo are only an example off one of our other tractors. I bought a new transmission cooler with these kind of fittings which I thought I would have been able to convert the hoses!!

 

[Pembs]

Would be surprised if Pirtek don't have fittings like that.
http://www.pirtek.co.uk/downloads/products/Hose and Fittings.pdf

Likely in there somewhere........

Will have a look through that thanks, anyone have any idea what these fittings might be called?

 

[Mursal]

Looks like you have enough wall on the cooler in/out to run a tap in to suit an available fitting?
Might be best not to use a tapered fitting (crack the narrow wall), use a copper washer to seal, if you can?

 

[mtx.jag]

Unfortunately the fitting in the photo are only an example off one of our other tractors. I bought a new transmission cooler with these kind of fittings which I thought I would have been able to convert the hoses!!

What part of the world are you,is it Pembrokeshire?

 

[Pembs]

Yes, thats right, Pembrokeshire

 

[mtx.jag]

I'm

Yes, thats right, Pembrokeshire

guessing you tryed Tom Smith and Glyn Thomas mathry? There a mobile bloke in a van to,spiratek I think..

 

[Pheasant Surprise]

Hi,

Anyone got any idea where we could get hydraulic fittings like shown in the picture?

Ideally, we would like to buy just the crimp on fittings instead of having to buy the whole pipe.

They connect onto the transmission cooler on New Holland TM series ( & 6080 etc.).

View attachment 311240 View attachment 311244

Close?

http://www.contitech.de/pages/produkte/schlauchleitungen/verschraubungen/verschraubungen_en.html

 

[Pembs]

I'm

guessing you tryed Tom Smith and Glyn Thomas mathry? There a mobile bloke in a van to,spiratek I think..

Have tried a few local people to no luck so far

 

[Pembs]

Close?
View attachment 311568

http://www.contitech.de/pages/produkte/schlauchleitungen/verschraubungen/verschraubungen_en.html

Thanks for the link, its quite close so will try and look into it more

 

[multi power]

It'll never weld having been exposed to oil, no matter how much you clean and wash it will sweat out a ruin the weld!!!

Really
It's not the first time I have welded fittings and stuff (well pigeon pooed together) and they always worked