Gapples
Member
Yes, 12 & 1455 have separate hydraulic tank.
The IH / Case Thread
- Thread starter blackieman83
- Start date
- Location
- South lakes
Spot of panel making, only part of rusty rot on her, bit of manipulation, few cuts n tweaks, weld/place then a bit more tweaking as you go along, then a bit of filler and red oxide for now, better than spending £50 quid for a corner and still have to do a make up piece either side!!
Attachments
bobajob
Member
- Location
- Sw Scotland
He did well to get going again after a gear change!
2wheels
Member
- Location
- aberdeenshire
didn't do the clutch much good by the sound of it.
- Location
- Crewkerne Somerset
Rebuilding the engine on my 414, as it wasnt running very well, only running on 3 and breathing well hardly any power or compression. Looked to have a chipped piston until took it out which realised the extent of the damage, lovely, all sorted now with new bits looking forward to getting it back together
- Location
- South lakes
refurbed the front grill, new headlights as chrome had gone in the old ones, mesh straightened and fixed back in place, after market headlights not that good a fit! piece of ali in the nose for now,
YELROM
Member
- Location
- North Yorkshire
Where did you get the headlights from as I could do with some for our 885
- Location
- South lakes
apukonline
2 Halogen bulb Headlight Headlamp 5 3/4 for Case International Harvester Tractor
Note: Please compare sizes before ordering. Fitting Diameter: 146mm (5 3/4") Bulbs Included Headlight bulb: H4 12V 100/90W P43T Halogen Side Light Bulb: 12V 5w Replaces the Sealed Beam units for Brighter Lights & New Bulbs
www.apukonline.com
Got a very sorry looking 574 on the yard.... awaiting some love and attention. Been on Farm for as long as I can remember so at least 35+ years. Had been the scraper tractor until it was parked up with clutch and brake issues 12 years ago. Was in dry storage for a couple of years but then got demoted to being outside. I know there is more issues as the starter motor has been removed and rain water has gone down the exhaust into the engine. Now I have a shed/garage I can put it in to fettle with it I can make a start..... But where do I start....? I'm not clued up on engines, but would like to think I can middle through with some help and pointers.
I did split it a few years ago to look at the clutch but then needed the shed to house stock so got put back together and left.... As she stands today-
Back in 2016 when I had my first attempt !
I did split it a few years ago to look at the clutch but then needed the shed to house stock so got put back together and left.... As she stands today-
Back in 2016 when I had my first attempt !
Attachments
Last edited:
- Location
- 200 miles N,NW of New York
Anyone got a source for a new sear for an 885xl, ?
Old seat suspension is fine, just the seat cushion and back is worn out,
Can't find replacement cushions online for it,
Old seat suspension is fine, just the seat cushion and back is worn out,
Can't find replacement cushions online for it,
YELROM
Member
- Location
- North Yorkshire
DS85CS - Grammer Seat Cushion Set | Intatrac UK Ltd
Order Grammer Seat Cushion Set DS85CS - Grammer Seat Cushion Set @
www.intatracuk.com
I think this is what we got for our 885
- Location
- 200 miles N,NW of New York
This tractor has a kab seat, so don't know if that will fit, I have googled it and cannot get parts for my seat as it looksDS85CS - Grammer Seat Cushion Set | Intatrac UK Ltd
Order Grammer Seat Cushion Set DS85CS - Grammer Seat Cushion Set @
I think this is what we got for our 885
YELROM
Member
- Location
- North Yorkshire
I will have a look at the seat next time I’m near our tractor but I’m sure we got the cushions from intrac and they just had a little D shackle that you pulled through the seat base and turned 90°
- Location
- 200 miles N,NW of New York
Aye no D shackles on this one,
Think anew seat will have to be the way forward
YELROM
Member
- Location
- North Yorkshire
Ours is a grammer seat, these are the clips that hold our cushion onAye no D shackles on this one,
Think anew seat will have to be the way forward
- Location
- 200 miles N,NW of New York
Thanks for going to the trouble of getting pictures, yes I know what you mean,
However this seat is not like that, its a cheap one than that and is different all together, it looked good till I took off the sweaty waterproof cover and household cushion
- Location
- South lakes
I have that seat on my digger, I got a new base off the Internet,
- Location
- 200 miles N,NW of New York
Any idea where you got it ?
- Location
- South lakes
Tek seating, it was a few yrs ago, +44 (0)1892 515028