Vicon rom Fert spreader
- Thread starter Tanker44
- Start date
- Location
- Essex/Herts Border
When you say last year do you mean last spring? Tray testing should really be done every year for every type of fert you use. Are you using the same type of fert as when you tested it? Even the same fert in different years/batches can spread differently. I've read somewhere before that if you can see striping your not just a few % out its a good 15-20% out! Assume the rate its putting it on is ok? Sounds like its just dropping it in completely the wrong point on the disc.
Yes last spring have the same Fert every year even at 21 metres it was striping also the book/app and online give different settings used a krm for 16 years never striped used same settings for different Fert apparently the driver before me had striping issues as well
Rust
Member
- Location
- Hertfordshire
Well it's set up. What you doing wrong.
Gears in wrong way around? Pto in 1000 or release timing wrong? Top link short?
Gears in wrong way around? Pto in 1000 or release timing wrong? Top link short?
I had a case once where fancy new spreader striped the whole farm.
Turned out if I remember correctly there were 2 types of disc for left and right sides. The machine had 2 discs the same.
Don’t assume anything when fault finding!
This very weekend we were going to fit some new 18m vanes on our spreader which were ordered in the winter. I called importer to just check I needed different vanes for 12m. The helpful chap there even gave me the part number.
Went to look in box and sure enough our new 18m vanes are.... you guessed it, 12m . Big striping effect narrowly avoided.
Turned out if I remember correctly there were 2 types of disc for left and right sides. The machine had 2 discs the same.
Don’t assume anything when fault finding!
This very weekend we were going to fit some new 18m vanes on our spreader which were ordered in the winter. I called importer to just check I needed different vanes for 12m. The helpful chap there even gave me the part number.
Went to look in box and sure enough our new 18m vanes are.... you guessed it, 12m . Big striping effect narrowly avoided.
- Location
- North West
By the sounds of it your spreading far too wide! As said, you really should test every product every year to be sure it won’t stripe. If you’ve not got a test kit get some trays from the garden centre and some tubes of eBay then it’s only a 10 minute job to check and you know it’s right.
It'll be a lot more sensitive to settings for different fert than krm .
I had issues last week with a blend that was doing as you say double either side of the tractor . Biggest issue was every size rest I took was different so just a stab in the dark with settings I just kept tray testing till I got close . That's with a kv so vicon in disguise
Pto is in 540 never checked gears assumed new machine you wouldn't have BUT the indicators were wired ass about face.As for top link height of machine adjusts as weight drops
- Location
- North West Wales
From what I remember with the older ones my first reaction would be that it’s hitting the disc in the wrong place
Tractortech
Member
- Location
- Cumbria
Now Then..
Check that the cups above the spinning discs are oriented correctly, the opening should face the centre of the machine 'ish'
Also, Check that you have the correct vanes for your desired spread width and they are fitted correctly.
If you're spreading a high sulphur content product, you'll need to clean the vanes often as that affects the spread patern..
Because it's a weighing spreader, it shouldn't go down when in use.. Have you got the rear linkage set to draft (ploughing) or position??
If it's a new machine, where's your dealers man??
Check that the cups above the spinning discs are oriented correctly, the opening should face the centre of the machine 'ish'
Also, Check that you have the correct vanes for your desired spread width and they are fitted correctly.
If you're spreading a high sulphur content product, you'll need to clean the vanes often as that affects the spread patern..
Because it's a weighing spreader, it shouldn't go down when in use.. Have you got the rear linkage set to draft (ploughing) or position??
If it's a new machine, where's your dealers man??
Can this be altered ?
- Location
- North West Wales
Oh, do they not have the lettering system on the shutters any more then
What age is your machine
2019
yes they do but on tray test was fine it’s spreading at 18 m fine just none behind tractor
- Location
- North West Wales
I’ve not done anything with them for over ten years, do they still come with the plastic box to determine the granular size? You could then set machine for prills or blend or granular size etc.
Is that a book for a rom??
KV TL is that the same ?
The London Palladium event “BPR Seminar”
This is our next step following the London rally 
BPR is not just a farming issue, it affects ALL business, it removes incentive to invest for growth
Join us @LondonPalladium on the 16th for beginning of UK business fight back
lwtheatres.co.uk
BPR is not just a farming issue, it affects ALL business, it removes incentive to invest for growth
Join us @LondonPalladium on the 16th for beginning of UK business fight back
BPR Summit | LW Theatres
lwtheatres.co.uk