ACEngineering
Last Activity:
Jun 16, 2019 at 10:55 PM
Joined:
Dec 9, 2014
Messages:
7,081
Likes Received:
4,432
Trophy Points:
143
Gender:
Male
Home Page:
Location:
Oxon
Occupation:
Spanners

Share This Page

ACEngineering

Member, Male, from Oxon

ACEngineering was last seen:
Jun 16, 2019 at 10:55 PM
    1. Dindiesel
      Dindiesel
      Hi,
      Ive a 2007 manitou 1740 ultra 1800hrs.
      I've the known fan bearing issue. Do you have a modified frame exchange for this type.
      Also my engine gearbox shaft has slight wear. (226235) is there a kit available for this type.
      Thanks
      Denis
      1. ACEngineering
        ACEngineering
        Hello yes there is an upgraded fan bracket available and an upgrade to the 226235 shaft or I can supply a Spicer aftermarket copy of original GKN shaft. I will PM you prices later.
        Jun 12, 2019 at 5:17 PM
    2. Combeland
      Combeland
      Hi Andy,

      I have a 2003 LM 410 with Dana axles. Could you tell me why they generate a positive air pressure inside? I know it is not unusual that then opening the bungs to check the oil level there is a sudden release of pressure, but as I am starting to get minor oil leaking on the inside of the hubs surely this can not be helping? Many thanks in advance
      1. ACEngineering
        ACEngineering
        its normal, the hubs don't have any vents on them, the axle does have a breather but is a ball and spring in it. Seals will expand tighter on the shafts with pressure behind them so they will seal better this way.

        Your seals are simply worn out, or you might have wheel bearing failure which is also common.
        Jun 2, 2019
    3. Chokess
      Chokess
      Hi ace I have a 2001 Manitou MLA 627 power shift that won’t go into 3rd or 4th gear. When it started the gears would come and go but now 3rd and 4th are completely gone. Would u have any idea of what wrong or where the problem is
      1. ACEngineering
        ACEngineering
        its either a 1998ish or a MLA 628? makes no odds though. will send you the electric solenoid sequence so you can check that other wise its internal so transmission overhaul job.
        Apr 27, 2019
    4. agrimax
      agrimax
      Hi Andrew, A poster looking a little assistance with a Manitou over on BFF if you're interested. Ta....
      1. ACEngineering likes this.
      2. ACEngineering
        ACEngineering
        Thanks, I do look in there now and again still.
        Apr 6, 2019
        agrimax likes this.
    5. Timbo
      Timbo
      Hi Andy, Could you quote me for a IS0841 Letrika which should be suitable for a Deutz DX 3 and 4 series please. Or whatever quality gear reduction flavour that will fit the F4L912 engine. Thanks.
      1. ACEngineering
        ACEngineering
        Out for Sunday dinner but will do later
        Feb 3, 2019
        Timbo likes this.
    6. hydraulic
      hydraulic
      sorry about that i accidentally locked the Conversation and did not know i did it until you sent message
      1. ACEngineering likes this.
    7. BreakerBell
      BreakerBell
      Hi Again Ace , was the hydraulic pump , the splines have wore right down . What price is a pump brand new not recon ? Or can I buy a new shaft ?
      1. ACEngineering
        ACEngineering
        Need serial number. I'll PM later.
        Oct 17, 2018
    8. BreakerBell
      BreakerBell
      Hi ACE , was checking an seen you say you do improved fan belts etc for the manitou. Iv a 05 machine , 634 lsu mlt . The belt is flapping about something terrible An making a clatter an also the bearing in the fan has a lot of movement / slap from side to side . Do you do a kit etc an how much ? Thanks craig .
      1. ACEngineering
        ACEngineering
        Hello, Yes common problem, there is an upgrade kit for the fan bracket, but I only use genuine belts, I did have a batch of over sized idler pulleys made which works quite well but I have sold them all and not had any more made yet. 2 types of bracket depending if standard fan or reverse fan.
        Oct 9, 2018
        BreakerBell likes this.
      2. BreakerBell
        BreakerBell
        Thanks Ace for getting back to me so quickly . Can you drop me a pm with your contact number an ill call tomorrow. Thanks craig .
        Oct 9, 2018
        ACEngineering likes this.
    9. icanshootwell
      icanshootwell
      Hi, just wondering if you had an idea on the price to supply a solenoid for the gear shift no 2, its for a cat 407 2009 model, i have serial no if that helps.
      Many thanks Graham
      1. ACEngineering
        ACEngineering
        I would have to use Finning's unless you can supply me the transmission make model and serial numbers etc otherwise you may as well contact finning's directly.
        Oct 9, 2018
        icanshootwell likes this.
    10. stablegirl
      stablegirl
      ACE do you sell filter kits, i have a 2013 634, merc engined machine ready for a service and we fancy doing it ourselves.

      Tom
      1. ACEngineering
        ACEngineering
        Hello
        Yes i sell all manitou parts.
        Aug 14, 2018
    11. Gary Moor
      Gary Moor
      I'd be grateful if I could get a copy of your MT 1337 SLT manual please?
      That so much
      Gary
    12. RRoy.07
      RRoy.07
      Hi, ACE

      I have manitou model MLT845-120 LSU, with engine Mercedes OM 904 LA. Currently my manitou hard to start and all the wiring cable is hot. Can I help with what information I need to do?

      Note : machine serial is 176141726091

      thanks

      regards,
      Roy
      1. ACEngineering
        ACEngineering
        You need a decent starter motor. The starter motor that was factory fitted and its genuine manitou replacement is really poor and not fit for the job.
        I supply a much better starter and cheaper.
        Jun 10, 2018
        RRoy.07 likes this.
      2. RRoy.07
        RRoy.07
        thank for recomendation ACE, do you have wiring schematic for this model? if there is whether it can be sent to me?
        Jun 11, 2018
    13. frenchesfarm
      frenchesfarm
      Andrew, what a fantastic service the starter arrived this morning fitted this aftenoon and guess what our manitou is now starting like its a car. Thank you for all your help. Totally recommend A+++
      1. ACEngineering likes this.
    14. Xpanhol
      Xpanhol
      Hi,

      Can you send me all information for Manitou Mt1637 SL with S/N-138878.

      The Manitou walks, but does not do spear movements.
      Repairs Manual Electrical and Hydraulic Diagrams I would be grateful.

      Best Regards,
      Nelson F.
    15. Highland Lad
      Highland Lad
      Hi,
      Could you please price A pair of hoses. Part No 222043 and a wiper motor Part No 563827 for a Manitou MT 1637 SL, Ser No 137594, Chassis No 1137594. And delivery to Fort William, Scotland, PH33 6SH.
      Cheers Robin.
      1. ACEngineering
        ACEngineering
        Will send you a pm
        Mar 15, 2018
    16. transparts NZ
      transparts NZ
      Hi from New Zealand .I have a manitou 730 That has had an engine fire and I need to buy a timing case,injector pump rocker cover etc Can you point me in the best direction please. These do not have to be new parts
    17. wobblechopper
      wobblechopper
      Hi, Would you mind if i emailed you for some advise on some faults on my manitou MLA628?
      1. View previous comments...
      2. ACEngineering
        ACEngineering
        Send me email and later on I'll go in to a bit more detail about system.
        Feb 9, 2018
      3. ACEngineering
        ACEngineering
        Does it have the brake filter under neath by rear axle? Might be blocked there was also a update to the early filters as they were not big enough for the flow..
        Feb 9, 2018
      4. wobblechopper
        wobblechopper
        I have sent a email. Cant say i have seen a filter?
        Feb 9, 2018
    18. Stewartry hill
      Stewartry hill
      Cable arrived cheque in post thanks very much
      1. ACEngineering likes this.
    19. classic cutter
      classic cutter
      hi
      how much is a iskra starter motor for a 1996 jcb 527-67 serial number 0577856 engine number u 757448b
      regards chris
      1. ACEngineering likes this.
    20. Stewartry hill
      Stewartry hill
      Sent a email
      1. ACEngineering likes this.
  • Loading...
  • Loading...
  • About

    Gender:
    Male
    Home Page:
    http://www.aandrhandling.co.uk/
    Location:
    Oxon
    Occupation:
    Spanners
    I'm an independent agricultural engineer specialising in service repair and spare parts supply for Manitou Telehandlers for construction and agriculture.

    Trading as A & R Handling I supply genuine and alternative parts all over the UK.

    www.aandrhandling.co.uk