Hello
We thinking of buying a new MF776X tedder
Two questions
1 any better performing alternatives for similar money
2 any suggestions for a good place to buy. Had a price from RVW Pugh so far
Thanks
Hello all
I am after a single phase, pto generator of about 25kva
Looking at second hand ones, they are all about 30 years old and cost £1500
Can anyone recomend a supplier of reasonable, new ones
Its for power cut use only
Thank you
Hello
Ive put it in Agricultural Matters as it is relevant to a lot of farmers
Weve had a call from a company, their web and email is btlocalbusiness.co.uk
They are saying our landline is no longer supported. Pur local ohine exchange will be switched off soon and any issues with the phone lines will not...
Hello.
Im afraid this is not a very positive post. More one to voice my concerns over the approach to the founder of Tilly Pass.
Until recently, I was "connected" to the founder, #Jane Gurney, on LinkedIn.
I appreciate many on here do not appreciate her organisation, though I always try and...
accident
analysis
death
drills
financial
flotation tyres
harvest
haulage
health
health and safety
insurance
loader
maintenance
management
operator
parts
performance
platform
red tractor
repair
sprayer
trading
training
transport
valtra
Hello...
We have some overgrown hedges that need cutting back.
We dont want to use a flail as it makes a lot of mess on the field whihc takes a lot of tidying up.
We were thinking of either a finger bar mower, or a saw blade (disc) on an excavator arm. Tidy up with a grab and then burn/chip...
Got a newish 5S.135. Its approaching time for a service.
A yellow light of a book and spanner has come on. Is this to say its service is due soon, or is there something else to worry about?
If it is a service light, can this be reset without dealer tools?
thank you
Hello...
So ive rebuilt the engine on the MK1 65 tractor.
I had new pistons liners, fuel pump and injectors refurbished. Head redone with new valves etc.
Set the timing up exactly as the manual.
Started it for first time yesterday and it was a pig to get going. Ran lovely and smooth, though...
Hello
As i progress tidying the 65 up, i need a new steering shaft ideally.
The MF part number is 1850589M91
This equates to a Sparex part S.43957, though i cannot find one. Any ideas?
I see a S.40277 which might be the same?
thanks
Has anybody got any feedback on the Quickie loader companion - the Quickie load measuring system.
We are contemplating fitting it to a loader and looking for feedback on this, and comparable systems
thank you
At the Royal Welsh, I signed up to "Airband" for their 4G internet service. Apparently they use a "special" antennae to boost the signal etc etc. It was all not work, no fee.
Anyway, over 2 weeks, they never contacted me to arrange the survey etc, so i thought if that is their customer service...
Hello
On the Hitachi EX60-2 track motor it started leaking hydraulic oil.
The hub is full of hydraulic oil.
Can anyone advise which part has gone. Ive done a bit of reading but a bit unsure tbh
@Jimmy Mc have you any idea?
thank you
Hello
We have a 4kw solar sytem on the shed. This is as much as teh DNO will allow.
I am thinking of installing a further 8KW on teh roof and a mechanism to prevent exporting more than the original 4kw.
Can I do this without notifying anyone? (its for my use and i wont be exporting any of it)
I...
Hello
So ive got round to starting to look at the 65.
Its a mark 1.
Does anyone have either en engine manual, or the torques and other various settings for it please? (A4.192 engine)
Ive undone all the head bolts but it wont budge - i assume its stuck on the head bolts?
Where do people...
back again
Our 1994 2cx has a Perkins engine. It has an engine build code AA, full code is AA 50429 U628185X
I believe this is a phaser 1004 engine and an early build type.
It is leaking water through the cylinder wall into the bore.
Ive been told it does not have a liner, it is machined block...
Hello.
Got a massey 6460 T2, with the Perkins 1000 engine (and VP44 pump, yes - that one)
The alternator bracket has snapped off the timing case (examining the fracture, its been broken a while).
Ive quickly asked a couple of people if they can weld it in place, both of whom have sadly declined...
Hello
Ive got a Raven Cruizer.
Today its stopped working and says "No GPS".
Does anyone have any ideas please? Is it likely the unit itself or the antennae kaput?
I see previously @Thick Farmer had one requiring repair - who fixes these things?
Struggle to spread fert without it nowadays :(...
i have a "small" sprayer boom (2 nozles only) which is fed from a 12v sprayer, like people use on a quad.
i had a solenoid valve which is not great. Im looking for sugegstions on what type of on off valve i could use please.
thanks
I need a new printer.
I cant decide whether to go for a cheap printer with cartridges, or a more expensive printer with "tanks" Im erring on the tank printer.
Can anyone recomend a decent printer witht he following spec
colour printer
scanner
duplex printing
wifi/ethernet connection
thanks!
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.