Search results

Hi, I have a 2017 T6.145 AutoCommand. It is currently stuck in the lower of two gears and won’t drive past about 10m/h I have a 2019 T7 AC and I know by pressing two buttons I can lock her in low range, this T6 however does not have this option to lock it and is still displaying speed to up to...

Put the TS115A under agitator today and when put her revs up smoke was coming heavily enough from manifold on top of the engine, white smoke. anyone have any ideas? Can I keep it working for the few days or is it serious?

Hi guys. looking to upgrade from a 2004 TM130 to a 2018 T6.145 AutoCommand. has anyone any experience with a T6.145 AC? My main job for the tractor will be ploughing with a four furrow plough. something the tm130 has little problem with, should the 145 pull away no problem or will it have its...

Hi guys. looking to upgrade from a TM130 to a T6.160 AutoCommand. has anyone any experience with a T6.160 AC or could point me in the right direction of one for sale. My main job for the tractor will be ploughing with a four furrow plough. something the tm130 has little problem with, should the...

Hi Guys, Have a 2019 autocommand and just curious as to spool/hydraulics settings, Is the only way to get the spools into float by using command grip (hand throttle) spool controls while pressing button on back of hand controller? on the levers it says forward is float but that’s not the case...

Hi, I’ve a 2009 New Holland CX8040. The combine has been throwing up these error codes for the past few years and last season they didn’t come up once and now this year on taking combine for a run prior to harvest they have reappeared….. pressure relief valve failure, shorted to high source...

Hi guys. Ive a 2019 T7.190 AutoCommand and recently the rear lift arms have started having a mind of their own. when I start the tractor and drive about the lift arms adjust to their own accord. When they are lifted to max on the screen it only shows as 80%(ish) when it should of course be...

Hi have a new T7.190 AC. It’s throwing up warning light on dash aswel as codes 18301 18323. And then cruise control stops working? This occurs when you pull the joystick back to slow down. Thanks.

Was out grubbing and error codes 14301 and 18323 came up and cruise control stopped working. Anyone have any ideas?

Have a 2013 TM310 and was using it this morning and about 15 minutes later went to start it again and wouldn’t start. Turn the key and nothing happens no lights no noise. As if the key is doing nothing. Everything seems to be plugged in behind the dash. Anyone have any idea? Relay maybe?

Have a new auto command. Was working in the dark and found it hard to see buttons on command grip (lever) Only have it a few months but I noticed when you start/stop the engine there are light that light up the buttons on it.. how do get them to turn on while working??

2019 New Holland T7.190 Autocommand wondering if my tractor has ISOBUS ready? The option is in the touchscreen but don't know what plug it is//where it is picture of the back end of my tractor

2019 New Holland t7.190 autcomman Does anyone know the difference between the standard HTS and the upgaded HTS II. my dealer told me you can update from 1 to 2. but what is the difference does anyone know? im wanting to use it on a round baler. press button spool valve pause spool valve go on...

Ive a CX8080 running off intelliview II monitor, the one before a touchscreen and would like a bigger screen with touchscreen, has anyone upgraded to III or IV? is it plug and play?

Hi Guys, have a 2004 TM130 Not sure if it has air con or not anyone know and easy way to tell? was going to get it regased if so.

Hi guys, Looking to purchase 2017/2018/2019 T6.175, T7.190, T7.210 or T7.225. Anyone know of anything that might be of interest, or any low priced EX-Hires. Thanks.