Does anyone have stock of precrimped wires for ampseal?
Did my system on my tractor ok, but losing my patience with doing it again on my sprayer!
Did my system on my tractor ok, but losing my patience with doing it again on my sprayer!
1.36£ 11% OFF|1 Ssts 8 14 23 35 Pin Amp 776273 1 770680 1 Auto Ecu Cablaggio Vrouwelijke Connettore Met draad 18Cm 776164 1 770680 1|Connectoren| - AliExpress
Smarter Shopping, Better Living! Aliexpress.comnl.aliexpress.com
Choose the correct one, ie 23 pin female.
You cannot buy an Ampseal plug for the price of these.
I ordered one last week and it came within 4 daysThanks. Thought there might have been somewhere with quicker delivery!
Not to worry!
Under the cab mat near the right hand door.Hi, I’m in the stages of starting to put all the hardware on the tractor and I’m struggling to find a cab pass through on my John Deere 6430 premium, I was wondering if anyone can help me here?
Thank you
Metal backing plate, 20cm diameter. Double sided tape to fix it to roof if it's a plastic one (no plate needed if metal ofc)What's the best to mount the antenna/receiver to the roof? (mf 6480) Just screw through and some rubber washers on it?
f9p have magnetic base, just place it on and when its right draw round it with a sharpy so if it gets rubbed under a branch you can just put it backWhat's the best to mount the antenna/receiver to the roof? (mf 6480) Just screw through and some rubber washers on it?
oh yes!!!The centre of the cab is not going to be the centre of tractor, so you will need to adjust or put offset in software.
A step up converter that will take 12v in and put out the voltage your laptop requires. I have been using a 100w so far, adjusted to 16v with Panasonic CF-C2 and FZ-G1 toughbooks.
100w dc step up converter for sale | eBay
Find great deals on eBay for 100w dc step up converter. Shop with confidence.www.ebay.co.uk
A connector to suit you device. I gather that toughbooks use an odd size, but a 2.5mm x 5.5mm x 9mm male connector jack is close enough. The 9mm long ones are a bit short, but work. There are 14mm long versions, but I haven't tried them.
Male DC Connector Jack 2.5 5.5 for sale | eBay
Find great deals on eBay for Male DC Connector Jack 2.5 5.5. Shop with confidence.www.ebay.co.uk
The jacks I have suit 5mm over all diameter cable. I use 1.0mm2 two core flex for a wiring various parts of my system. It's a bit excessive for handling 100w, but is 5mm over all diameter cable, a nice size to handle and I already have a roll of the stuff.
Round Twin Core 2 x 1mm² Thin Wall Auto Cable - 16.5 Amp [ALM Part Reference - TC1R] - £0.00 : ALM Solutions, Auto Electrical Parts and Accessories for Cars, Boats, Caravans and Campers
ALM Solutions Round Twin Core 2 x 1mm² Thin Wall Auto Cable - 16.5 Amp [ALM Part Reference - TC1R] - Product Information High temperature thin wall low voltage cables suitable for use in the automotive, marine and allied industries. These cables are specified as standard by manufacturers...www.almsolutions.co.uk
I put it in it's own 3d printed case, but if you have a large enough project box for other agopen boards then it could fit in there. I have a switched 12v output from the boxes with my v2 boards in, which powers these chargers for the toughbook and also other devices such as ethernet hub and section control module. I'm just using spade connections for the time being on the input, but ideally will switch to powerpole or superseal connectors instead to help avoid connecting the power the wrong way.
View attachment 1138033
The red board is a 150w step up converter I have just got, waiting to go in another tractor. More powerful than needed, but just happened to be slightly cheaper and has the advantage of screw terminals, so a little less soldering to do.
didn't see the mesh top and bottom, v cleverThe box has a mesh top and bottom. I haven't noticed them getting warm at all.
The wobbling will be the valve oscillating, it does that if setting aren't right.Looks like alot of play in your steering rams/track rod ends the way the wheels were wobbling. Mightve been better to be actually sat in the cab while videoing stuff like that, way to much that could go wrong