Cattle clippers

Jackov Altraids

Member
Livestock Farmer
Location
Devon
I think I'm going to finally give up on using my sheep shearing gear to clip cattle and would greatly appreciate any advice / recommendations on what to buy.
I sell most off grass so only need to do a few, so not looking to spend too much. I'm thinking it won't take saving many clipping charges to pay for a set.
 

hubbahubba

Member
Location
Sunny Glasgow

I recently got a set of these for dagging lambs. Clipped 80 spring calves backs with one comb and cutter. Recharge battery once. Should of got a set years ago.
 

An Gof

Member
Location
Cornwall
I think I'm going to finally give up on using my sheep shearing gear to clip cattle and would greatly appreciate any advice / recommendations on what to buy.
I sell most off grass so only need to do a few, so not looking to spend too much. I'm thinking it won't take saving many clipping charges to pay for a set.

I used to use a sheep shearing handpiece. Just bought a set of Heinger Explorer cordless clippers which are currently on offer at MVF http://m.molevalleyfarmers.com/h5/r...e/products/heiniger-xplorer-clipper-pack-2019

Absolutely delighted with them so far. But I’m only trimmining backs, not shi**y bellies. They came recommended to me on another recent TFF thread on cattle clippers.

 

Half Pipe

Member

I recently got a set of these for dagging lambs. Clipped 80 spring calves backs with one comb and cutter. Recharge battery once. Should of got a set years ago.
These look same clippers with different stickers
 

Jackov Altraids

Member
Livestock Farmer
Location
Devon
These look same clippers with different stickers

The body looks exactly the same but the spec's are slightly different;
Razor

Voltage11.1v
Cut Speed2800rpm
Weight1.5kg
Grip Diameter47mm
Power SourceLi-ion Battery 11.1v (6000mAh)
Motor Power200 watts

Masterclip Outback Dirty Cattle Clipper
  • 200W motor
  • Voltage DC12V
  • 2500 rpm cutting speed
  • 2 x 6000 mAh li-ion batteries
  • Weight 1.5Kg

Which would be better?
 

Jonny B88

Member
Location
ballykelly. NI
I bought the outback ones from masterclip this autumn. I bought it mostly to clip tails and backs. I am pleased with them they handle very dirty tails and backends well. Batteries are ok too so far although early days. I have given it a fair bit of work. I bought it after seeing a dairy farmer friend using one for tails and he was very pleased with them.

Out of curiosity what do you guys clip for the factory’s?
 

jamj

Member
Location
Down
I used to use a sheep shearing handpiece. Just bought a set of Heinger Explorer cordless clippers which are currently on offer at MVF http://m.molevalleyfarmers.com/h5/r...e/products/heiniger-xplorer-clipper-pack-2019

Absolutely delighted with them so far. But I’m only trimmining backs, not shi**y bellies. They came recommended to me on another recent TFF thread on cattle clippers.

I have bought a set of these and they are comfortable to use, with low vibration.
However the set has only finer blades which are not much use for dirt removal. I enquired about blades for sheep which would be ideal but discovered that the sheep blades do NOT fit this machine!
Different heads, and different blades.
You can get coarse blades but whether they are any good on the dirtier parts I don't know.

I just thought that I should flag this up in case anyone else is caught out.
 

An Gof

Member
Location
Cornwall
I have bought a set of these and they are comfortable to use, with low vibration.
However the set has only finer blades which are not much use for dirt removal. I enquired about blades for sheep which would be ideal but discovered that the sheep blades do NOT fit this machine!
Different heads, and different blades.
You can get coarse blades but whether they are any good on the dirtier parts I don't know.

I just thought that I should flag this up in case anyone else is caught out.

Two sets of blades in the kit, one fine and one coarse. Both seem to work OK but i clipped all the backs on my cattle as they were housed so backs were all clean. Haven't tried it on soiled areas yet
 

jamj

Member
Location
Down
Two sets of blades in the kit, one fine and one coarse. Both seem to work OK but i clipped all the backs on my cattle as they were housed so backs were all clean. Haven't tried it on soiled areas yet
As far as I remember the two sets are fine and thoroughbred, which is also quite fine.
Just don't understand why they don't make sheep blades for them as well.
 

Jackov Altraids

Member
Livestock Farmer
Location
Devon
I bought the outback ones from masterclip this autumn. I bought it mostly to clip tails and backs. I am pleased with them they handle very dirty tails and backends well. Batteries are ok too so far although early days. I have given it a fair bit of work. I bought it after seeing a dairy farmer friend using one for tails and he was very pleased with them.

Out of curiosity what do you guys clip for the factory’s?

Thanks, I will be getting the Masterclip outback cordless.

My understanding is that you pretty much have to clip off any dirt. Knees, brisket, belly and back legs to the point there really isn't any point in leaving anything.
 

Half Pipe

Member
Thanks, I will be getting the Masterclip outback cordless.

My understanding is that you pretty much have to clip off any dirt. Knees, brisket, belly and back legs to the point there really isn't any point in leaving anything.
If your clipping dirty cattle get a can of spray oil, it's good for quick clean of blades, use it bit like a hand held pressure washer.
Something like this
Smells like hair salon but does good job, half the price if you do quick Google search.
 

Whitepeak

Member
Livestock Farmer
As far as I remember the two sets are fine and thoroughbred, which is also quite fine.
Just don't understand why they don't make sheep blades for them as well.
Heineger standard combs have 31 teeth, same as the fine (31F), the coarse ones have 21 teeth. They don't do anything more coarse or less teeth than that. Although some other makes are compatible with Heineger clippers.
I get on fine clipping tails and backs with standard combs with our Heineger Xperience.
 

Jackov Altraids

Member
Livestock Farmer
Location
Devon
@Jackov Altraids what did you buy in the end and how are you getting on with them?

I bought the masterclip;

Several places sell them and just stick their name on them, Masterclip were cheapest at the time and were excellent to deal with.
I really haven't used them enough to give any useful comments. It seems quite heavy and long when in your hand. I chose it over 'clippers' as I thought I could then use it on sheep which I have done more than cattle.
 

Jackov Altraids

Member
Livestock Farmer
Location
Devon
They will do the job but i would imagine 'clippers' would be easier to get under clods of dirt as they would be thinner than the sheep combs and cutters.
I can really say as I've never used anything else but having a battery handpiece is a lot better in a crush than getting power and a flexidrive.
 

johnspeehs

Member
Location
Co Antrim
Anyone else have any problem with the batteries? one of mine has given up after 18 months and done very little, my neighbours something similar?, not cheap to replace.
 

SFI - What % were you taking out of production?

  • 0 %

    Votes: 104 40.6%
  • Up to 25%

    Votes: 93 36.3%
  • 25-50%

    Votes: 39 15.2%
  • 50-75%

    Votes: 5 2.0%
  • 75-100%

    Votes: 3 1.2%
  • 100% I’ve had enough of farming!

    Votes: 12 4.7%

May Event: The most profitable farm diversification strategy 2024 - Mobile Data Centres

  • 1,556
  • 29
With just a internet connection and a plug socket you too can join over 70 farms currently earning up to £1.27 ppkw ~ 201% ROI

Register Here: https://www.eventbrite.com/e/the-mo...2024-mobile-data-centres-tickets-871045770347

Tuesday, May 21 · 10am - 2pm GMT+1

Location: Village Hotel Bury, Rochdale Road, Bury, BL9 7BQ

The Farming Forum has teamed up with the award winning hardware manufacturer Easy Compute to bring you an educational talk about how AI and blockchain technology is helping farmers to diversify their land.

Over the past 7 years, Easy Compute have been working with farmers, agricultural businesses, and renewable energy farms all across the UK to help turn leftover space into mini data centres. With...
Top