Connor bale wrapper problems

[Greythundercloudys]

I'm still no further forward with this machine, as l said before it pulls the bales over on to the black holder and ripped the plastic, lv had that many bales this year with mold on this corner, driving me crazy, l will need to fix it for this year, if there is a this year, was told the belts, they are kind canvas no rubber but they all seem the same tension. Maybe l should just renew them all, where can you buy ones that's not to crazy priced.

 

[Tractortech]

Now Then..
It's not something completely daft like the film dispenser being bolted on the wrong side of the bracket / drawbar??
I assume it's the film dispenser that is in contact with the bale??

 

[Greythundercloudys]

No, the bales comes over to this black bobbin, the opposite side from the plastic stretchers.

 

[Dave W]

Can you post some pictures. Ideally from overhead.

 

[Greythundercloudys]

I will try.

 

[Greythundercloudys]

Can't get pic to load, what are you looking to see from above?.

 

[Dave W]

Can't get pic to load, what are you looking to see from above?.

Anything that might be obvious to a different pair of eyes. It's almost impossible to diagnose from a written description

 

[H200GT]

There can only be three things that makes the bales go to one side, and that has to be poor cone shaped bales, issue with the bed rollers not being parallel, or bed belts of different lengths.

Id measure the bed roller bearing centres first to make sure they are parallel.

Even if the bale goes to one side is shouldn't rip the plastic, unless there is huge pressure onto the one roller. Do the side rollers turn?

 

[Greythundercloudys]

The bales are nice round bales, it doesn't matter if you put the bale over to the opposite cone but about 9 turns it pulled over on to the other one and ripping the plastic against it, but everything seems normal but it isn't.

 

[Tractortech]

Have you got too much stretch on the film?? I remember some were adjustable, probably many years ago though

 

[Greythundercloudys]

No l don't think so

 

[Greythundercloudys]

One of the end belts is abit slack, so lm going to try tightening it a wee bit.

 

[sulky]

I'm still no further forward with this machine, as l said before it pulls the bales over on to the black holder and ripped the plastic, lv had that many bales this year with mold on this corner, driving me crazy, l will need to fix it for this year, if there is a this year, was told the belts, they are kind canvas no rubber but they all seem the same tension. Maybe l should just renew them all, where can you buy ones that's not to crazy priced.

i had the same thing with an old wrap-rite wrapper it was the rollers not been paralel we even used to have it set out of level on the ground ,then measured width between rollers someone had tightened the belts more on one side causing the bale to move to the wide end and rub bad against the bobbin / after we ajusted correctly had to swoop belts around as that end had stretched

 

[Greythundercloudys]

I phoned conor, spoke to a very helpful man, he said one end belt would be slightly slacker than the rest, so he said there is a bit movement if you slacken the baring bracket, so time will tell.

 

[ILovebaling]

Think mine does this as well, I don't use it anymore if I can help it, easiest way to solve the problem I found

 

[Greythundercloudys]

I saw a very clean conor wrapper for sale, full auto, 3950 but since this virus l will try and fix my old one or maybe triple wrap them all.

 

[Deccarroll]

Have a problem with a conor 9700 when you wrap the bale, cut and tie, tip off the bale , load the next bale onto the wrapper , the plastic is coming out of the cut n tie holder after one revolution of the wrapper “when it should b two revolutions I think”dose anyone know what my problem is

 

[Netherfield]

There must be settings in the controller.