Direct/Strip-till drilling photo gallery

[juke]

I should be claiming a royalty on those front discs, i told claydons a few years ago they needed to fit discs on the front

They must have listened we got them in 2015

 

[Case290]

I should be claiming a royalty on those front discs, i told claydons a few years ago they needed to fit discs on the front

The cost of them they would probably say that’s fine .

 

[juke]

The cost of them they would probably say that’s fine .

Gotta think positive , nice little fuel saving not pulling the tines through the ground so much.

 

[juke]

First of the beans through there, looks like every seed has germinated

 

[YELROM]

Moores drilled wheat into 4year grass ley

 

[Case290]

will the discs fit my v drill ? The gap between front and rear may not be big enough ?

 

[Case290]

View attachment 735360
Moores drilled wheat into 4year grass ley

That look good and thick . I think every ones wheat looks thicker this year.

 

[Michael S]

View attachment 735360
Moores drilled wheat into 4year grass ley

Looks good. I have used a Moore drill for over 25 years and continue to do so, although we often struggle to get it in the ground in the presence of much surface trash in no-till situations. Works well in tillage situations and no-till after crops like peas, stripped linseed and spring rape. Great all round drill.

 

[juke]

View attachment 735386 will the discs fit my v drill ? The gap between front and rear may not be big enough ?

I wouldn't like to say to be honest, I'd ask the question to someone at Claydons.

 

[Daniel]

Wasn't sure if the wheat would push through this much spring barley trash?

Will it's decomposition cause problems?

 

[average farmer]

View attachment 735386 will the discs fit my v drill ? The gap between front and rear may not be big enough ?

Whats the pipe for cable tied to the back of the seed pipe?

 

[Case290]

I have a Front tank for Fert if need be. The pipe just drops Fert in the trench the a share makes works v well. I did see claydon are doing it on the new drills now.

 

[Devon James]

View attachment 735386 will the discs fit my v drill ? The gap between front and rear may not be big enough ?

Nice mod to be able to use the Hybrid leading tine

 

[Daniel]

I should be claiming a royalty on those front discs, i told claydons a few years ago they needed to fit discs on the front

These chaps have made a set of cutting discs for the front links, good idea for getting the drill to go through a lot of trash without having to spend ages swapping discs and tines?

 

[Warp Land Farmer]

These chaps have made a set of cutting discs for the front links, good idea for getting the drill to go through a lot of trash without having to spend ages swapping discs and tines?

They seem to rate it but was their reasoning front weight rather than trash cutting? Would like to of seen the drill working the same field with the discs out of work.

 

[Badshot]

@strip-till-phil used to have a straight disc setup on the front.

 

[juke]

These chaps have made a set of cutting discs for the front links, good idea for getting the drill to go through a lot of trash without having to spend ages swapping discs and tines?

Those discs aren't doing the same job as you get using the claydon replacement discs mounted to the drill.

 

[Case290]

Claydon say the front cutting discs would fit my v drill . As it has the hybrid leg brackets.

 

[Daniel]

Those discs aren't doing the same job as you get using the claydon replacement discs mounted to the drill.

They'll cut through the trash and you keep the front tine so getting the shatter effect as well?

 

[Brisel]

Not much good on my hills but a good simple idea for flat land