Kverneland es

[farmerjimz]

I just got a new Es 100 with the 200 headstock , hydraulic front furrow width and memory
Do i have to set up the aligment of the plough, and what does the valve on the working width cylinder does
Thanks in advance

 

[KB6930]

The valve on the ram simply turns it off for transport.
There's no alignment adjustment on an ES

 

[farmerjimz]

The valve on the ram simply turns it off for transport.
There's no alignment adjustment on an ES

What is turning off ?

 

[KB6930]

What is turning off ?

You're (supposed) to turn it off once you've pulled it in for road travel .

 

[KB6930]

On an es like you have you'll need 3 double acting spools
1 for front furrow
1 for turnover
1 to set the width with memory ram

Turnover spool will pull plough in turn it over then push it back out to the set width.

Memory ram one will alter the width from 12 to 20 inch so you set your max width with this .

Both turnover and vari width can be used in the move

Keep your front furrow slide well greased it's never keen to move at the best of times

 

[farmerjimz]

On an es like you have you'll need 3 double acting spools
1 for front furrow
1 for turnover
1 to set the width with memory ram

Turnover spool will pull plough in turn it over then push it back out to the set width.

Memory ram one will alter the width from 12 to 20 inch so you set your max width with this .

Both turnover and vari width can be used in the move

Keep your front furrow slide well greased it's never keen to move at the best of times

Thanks a lot
You really helped me

 

[KB6930]

Thanks a lot
You really helped me

They're an easy plough to figure out you'll get on fine

 

[daveydiesel1]

How do you set alignment to know when irs pulling dead true? Like whatdo you measure

 

[KB6930]

@daveydiesel1 Just look at your top link there's no adjustments to be made they just work

 

[daveydiesel1]

@daveydiesel1 Just look at your top link there's no adjustments to be made they just work

Sorry my plough is a new holland, theres an alignment setting but i was wondering how to measure to know if its running true

 

[KB6930]

Sorry my plough is a new holland, theres an alignment setting but i was wondering how to measure to know if its running true

Can't help you there I never measure anything I just tinker till it looks right

 

[brentnz]

I just got a new Es 100 with the 200 headstock , hydraulic front furrow width and memory
Do i have to set up the aligment of the plough, and what does the valve on the working width cylinder does
Thanks in advance

Ideally a the distance between the inside sidewalls of the tyres on the front axle is the same as that of the rear axle

 

[daveydiesel1]

Ideally a the distance between the inside sidewalls of the tyres on the front axle is the same as that of the rear axle

Shel never make a job of it if theyr not running in line

 

[farmerjimz]

Shel never make a job of it if theyr not running in line

I read that kverneland 's variwidth system has autoalligment, so i guess it will aleays pull straight

 

[KB6930]

I read that kverneland 's variwidth system has autoalligment, so i guess it will aleays pull straight

An EG has alignment adjustment es doesn't they're made straight so pull straight

 

[daveydiesel1]

I read that kverneland 's variwidth system has autoalligment, so i guess it will aleays pull straight

But if the tractor isnt pulling straight itl still be off

 

[farmerjimz]

This crosshaft is not exactly in the middle
Should i adjust it ??

 

[KB6930]

This crosshaft is not exactly in the middle
Should i adjust it ??

Won't be too important depending how much it's off .

You might need to swap the plates it's in from side to side to get it closer to the tractor if you're struggling for top link length . But that might be the 250 headstock now I think about it I can't remember needing to do a 200in the past

 

[farmerjimz]

Won't be too important depending how much it's off .

You might need to swap the plates it's in from side to side to get it closer to the tractor if you're struggling for top link length . But that might be the 250 headstock now I think about it I can't remember needing to do a 200in the past

I mean that the crosshaft is 3 cm to the right

 

[KB6930]

This crosshaft is not exactly in the middle
Should i adjust it ??

The only other thing that might need turned is the slide the front furrow goes on depending on your track width of your tyres.

It's got 2 positions I did mine when I needed to but get the dealer to do it if required