Kverneland plough changeover valve

[Bob1234]

Got an issue with my 3 furrow reversible, its struggling to turnover and will go halfway then stop. I can get it to turnover if I work the spool back and forth slowly. Will it be a bit of dirt stuck in it? Or should I try adjusting the screw?

Thanks

 

[Chae1]

Could be worse. Broke mine in 2 again yesterday.

 

[Bob1234]

[emoji54][emoji54][emoji85]

 

[Billboy1]

Got an issue with my 3 furrow reversible, its struggling to turnover and will go halfway then stop. I can get it to turnover if I work the spool back and forth slowly. Will it be a bit of dirt stuck in it? Or should I try adjusting the screw?

Thanks

Had mine go on 5 furrow , looks the same I bought a 2nd hand one off westlake plough parts 1/4 of price of new ,good service
Ps about £700 new [emoji15]

 

[robo]

had same problem with ours years ago . fitter took it apart cleaned it all with brake cleaner, back together perfect. just remember what fits where

 

[Chae1]

Just replace it. I spent hours fudging about with ours.

Been fine since.

 

[quattro]

Could be worse. Broke mine in 2 again yesterday.

You need a 6 furrow semi mounted Kongskilde x demo (I just happen to have one sitting here)

 

[Chae1]

Just got that one fixed again!

I was speaking to someone from your area wanting another overum semi mounted, think the first ones were good value for money.

Does Mr Grubb run kongskildes now?

 

[quattro]

Just got that one fixed again!

I was speaking to someone from your area wanting another overum semi mounted, think the first ones were good value for money.

Does Mr Grubb run kongskildes now?

2kongskildes and a new Holland same plough

 

[Bob1234]

Got a new valve from flowfit for £160 specced for the size of ram on the plough,
Its still the same if not worse now[emoji85]. Tried adjusting the set screw and the P.R. Valve but it wont go over centre?‍[emoji24]. I can get it to flip over with the old valve if you back and forward a bit with the spool lever.

Anyone any ideas? [emoji51]

 

[Bob1234]

 

[Chae1]

Buy a genuine one.

 

[njneer]

Used to find that working the spool to turn the plough over then flicking the lever the opposite way when the plough just overcentred was the best way to get them to turn over once they start that.
Get good at it after a while and forget about it.
It could be a bit of dirt somewhere but usually just the valve worn out and internal leakage.
New ones not cheap and difficult to source non original but sometimes better than the hassle and frustration.

 

[Bury the Trash]

Got a new valve from flowfit for £160 specced for the size of ram on the plough,
Its still the same if not worse now[emoji85]. Tried adjusting the set screw and the P.R. Valve but it wont go over centre?‍[emoji24]. I can get it to flip over with the old valve if you back and forward a bit with the spool lever.

Anyone any ideas? [emoji51]

What about the tractor valve, try a different one
Ram problem?
.....with the seals inside the ram .

or maybe a lot wear /slop on the pins ?

 

[glasshouse]

Got a new valve from flowfit for £160 specced for the size of ram on the plough,
Its still the same if not worse now[emoji85]. Tried adjusting the set screw and the P.R. Valve but it wont go over centre?‍[emoji24]. I can get it to flip over with the old valve if you back and forward a bit with the spool lever.

Anyone any ideas? [emoji51]

Just plumb your hoses straight to ram

 

[glasshouse]

I fitted a new b

Used to find that working the spool to turn the plough over then flicking the lever the opposite way when the plough just overcentred was the best way to get them to turn over once they start that.
Get good at it after a while and forget about it.
It could be a bit of dirt somewhere but usually just the valve worn out and internal leakage.
New ones not cheap and difficult to source non original but sometimes better than the hassle and frustration.

I fitted a newbox last yr, £1000 and no different

 

[TheEarlOfMoray]

I got a seal kit a few years ago as I thought it would sort the problem. Was £200 I think but made no difference

 

[glasshouse]

What about turnover ram seals?

 

[Chae1]

I fitted a new b

I fitted a newbox last yr, £1000 and no different

Did you get your money back?

 

[glasshouse]

Did you get your money back?

Haha