pto stub shaft

[Forever Fendt]

Would any one know where i could get a 1 3/4" splined pro shaft about 400mm long total to cut a keyway in it and a couple of bearings on it for a saw bench modification thanks

 

[davidroberts30]

Would any one know where i could get a 1 3/4" splined pro shaft about 400mm long total to cut a keyway in it and a couple of bearings on it for a saw bench modification thanks

Lely mower drive shafts were similar

 

[Forever Fendt]

Lely mower drive shafts were similar

i can find new ones but mostly 1 3/8 and very short about 9" but need longer to get 2 bearings and sprocket in middle

 

[pine_guy]

i can find new ones but mostly 1 3/8 and very short about 9" but need longer to get 2 bearings and sprocket in middle

Would it not be easier to take a whole drive shaft assembly, pully, bearings and all to do the conversion. No idea, just a thought.

 

[Forever Fendt]

Would it not be easier to take a whole drive shaft assembly, pully, bearings and all to do the conversion. No idea, just a thought.

not really its a bit tight for room to be fair

 

[miniconnect]

How about a lower shaft and bearings off the front of a rotaspreader? Ours is splined shaft about 12 or more inches long with a duplex sprocket in the middle of two bearings.

 

[Bob c]

Would any one know where i could get a 1 3/4" splined pro shaft about 400mm long total to cut a keyway in it and a couple of bearings on it for a saw bench modification thanks

pto spline one end ?
all the ones i find 350mm long and are 1 3/8"

 

[Netherfield]

Old Hillam , Fraser , Rotorspreader.

 

[davidroberts30]

i can find new ones but mostly 1 3/8 and very short about 9" but need longer to get 2 bearings and sprocket in middle

I'll measure the 1 here later

 

[Speedstar]

Think I may have a new one in the workshop out of s wholecrop header

 

[Forever Fendt]

pto spline one end ?
all the ones i find 350mm long and are 1 3/8"

I just fancy having the bearings a little bigger and not taking to much meat out of the shaft with cutting a key way

 

[Barleymow]

agrihire

 

[davidroberts30]

I'll measure the 1 here later

 

[Bob c]

View attachment 780474 View attachment 780476 View attachment 780480 View attachment 780482 View attachment 780484 View attachment 780486

2nd dibs please
if its no good for @Forever Fendt job

 

[davidroberts30]

2nd dibs please
if its no good for @Forever Fendt job

If you want it for a mower I'll tell you now and @Forever Fendt it's been repaired .in the second pic up from bottom it snapped right where the jaws of the caliper are and I drilled both bits out and made a dowels,shamfered both broken edges and welded it back and turned it back to size .

We.found a second hand shaft to keep our mower going and I repaired this 1 one rainy day after

 

[Bob c]

If you want it for a mower I'll tell you now and @Forever Fendt it's been repaired .in the second pic up from bottom it snapped right where the jaws of the caliper are and I drilled both bits out and made a dowels,shamfered both broken edges and welded it back and turned it back to size .

We.found a second hand shaft to keep our mower going and I repaired this 1 one rainy day after

need to make 3 point linkage frame
to carry the pto and a pto hyd pump for my bale sledge

 

[Forever Fendt]

If you want it for a mower I'll tell you now and @Forever Fendt it's been repaired .in the second pic up from bottom it snapped right where the jaws of the caliper are and I drilled both bits out and made a dowels,shamfered both broken edges and welded it back and turned it back to size .

We.found a second hand shaft to keep our mower going and I repaired this 1 one rainy day after

You are a star for taking the trouble to measure it,But if it has been repaired and i need to have a keyway milled in it i would probably look for a complete one to be safe so over to you @Bob c but thanks anyway

 

[Bob c]

You are a star for taking the trouble to measure it,But if it has been repaired and i need to have a keyway milled in it i would probably look for a complete one to be safe so over to you @Bob c but thanks anyway

thinking the same as you realy
it breaking while baling and us down ,...sorry
can see why its been repaired,...back up spare

 

[davidroberts30]

You are a star for taking the trouble to measure it,But if it has been repaired and i need to have a keyway milled in it i would probably look for a complete one to be safe so over to you @Bob c but thanks anyway

There is a key way in it near the caliper in second last pic

 

[davidroberts30]

need to make 3 point linkage frame
to carry the pto and a pto hyd pump for my bale sledge

It would do that fine