Steel bushes

[Jack Russell]

I need a few steel bushes for a machine. They are just over 16mm ID so that they can take an M16 bolt. OD needs to be 22mm/23mm. Width or depth is 15mm. Where would be best to get something like this?

 

[mobileweld]

Probably best off getting a local firm to spin some out on a lathe. Simple enough and will be supporting local. If no luck then I’ll have a look online and see what I can find for you

 

[Kidds]

If you can't find local there are folk on ebay that will do it and no doubt google will find you an online service too.

 

[Lincoln75]

I need a few steel bushes for a machine. They are just over 16mm ID so that they can take an M16 bolt. OD needs to be 22mm/23mm. Width or depth is 15mm. Where would be best to get something like this?

If you have leeway then shaft collars may do that job.

Bearingboys

Online

www.bearingboys.co.uk

 

[76masseyman]

Is it something Mr Croft, up the road could do ?

 

[startinghandle]

There's local guy expert at the job in Mid Wales which is probably not much use to you

 

[Mickstup]

There's local guy expert at the job in Mid Wales which is probably not much use to you

Who's that, as I need something similar. TIA.

 

[startinghandle]

Who's that, as I need something similar. TIA.

I will send details indirectly

 

[Mickstup]

I will send details indirectly

Thanks.

 

[Alchad]

Any use?

Mild Steel Precision Round Tube Pipe Many sizes lengths Metal Bar Rod Strip 1 | eBay

Discover the superior quality and performance of the Mild Steel AISI 1010 Seamless Precision Steel Tube. Specialising in mild steel, this tube presents an unrivalled mix of durability and flexibility.

www.ebay.co.uk

Alchad

 

[Sharpy]

I need a few steel bushes for a machine. They are just over 16mm ID so that they can take an M16 bolt. OD needs to be 22mm/23mm. Width or depth is 15mm. Where would be best to get something like this?

Get some round bar and drill it out?

 

[devonbeef]

Any use?

Mild Steel Precision Round Tube Pipe Many sizes lengths Metal Bar Rod Strip 1 | eBay

Discover the superior quality and performance of the Mild Steel AISI 1010 Seamless Precision Steel Tube. Specialising in mild steel, this tube presents an unrivalled mix of durability and flexibility.

www.ebay.co.uk

Alchad

I have severals pins on different machines with slop in pins was wondering the same line, older machines . Was thinking thick pipe ,and weld in, not sure how long it would last, have to be better than sloppy pins and letting them wear more.

 

[devonbeef]

I have severals pins on different machines with slop in pins was wondering the same line, older machines . Was thinking thick pipe ,and weld in, not sure how long it would last, have to be better than sloppy pins and letting them wear more.

I guess some of these oilite bushes (bearing boys)take up some slop but cant be welded in with stick welder

 

[Chuckie]

I guess some of these oilite bushes (bearing boys)take up some slop but cant be welded in with stick welder

They are very soft, steel would be better

 

[JohnBoy]

I have severals pins on different machines with slop in pins was wondering the same line, older machines . Was thinking thick pipe ,and weld in, not sure how long it would last, have to be better than sloppy pins and letting them wear more.

It's fierce handy stuff. It's like a length of hole

 

[shumungus]

It's fierce handy stuff. It's like a length of hole

What a lovely description.

 

[devonbeef]

can you get hardened steel bushes to weld in, i can not seem to find any on line which are thin enough to weld in worn pin holes?

 

[clbarclay]

Any worn pin hole will be oval to some extend and need drilling or reaming out to be round.

I have repaired worn pivot holes with bushes like these and a lot of effort with adjustable reams to make them a good tight fit.

Plain Bearing Bushes PTFE lined - WychBearings.co.uk

Wych Bearings - Buy Online. Bearing Supplier, Housed Bearings, Oil Seals, Adhesives, Lubricants, Roller Chains, Sprockets and Engineering Supplies. Service from your local Bearing Supplier, Nationwide.

www.wychbearings.co.uk

 

[clbarclay]

For really badly worn holes, I would like to get a mag drill to get them round again and then turn up some bushes to the broach and pin sizes.

 

[ACEngineering]

It's fierce handy stuff. It's like a length of hole

Best debur the edge first can be a bit sharp