Need a part for our quick hitch but I’m unsure of the make, anyone any ideas?
Cheers
The part circled in red is where the broken part is/was, thinking it’s a spring plate that keeps the locking flap closed.
Thanks
Was looking for this website earlier but couldn’t find it. I’m looking for the old school forum that had the knowledgable Rick guy on it? Rick corbly I think?
Needing to change the hub seal on this tractor. I’ve made a pulled to pull pins out with M18 threaded bar but they’re a hell of a tight and won’t move. Are they pressed into the axle? Thinking it’s going to need some heat to remove them. Anyone done them before?
Just took first cut off and going to be applying slurry via umbilical this week. It’s been dry here for the last 2 weeks and ground pretty hard now. Forecast looks dry for the foreseeable future. Should I apply the slurry with my dribble bar or will that leave it in dry lines(but leave the grass...
Just discing some fields after they’ve been burnt off. Going to be power harrowing then now prior to grass sowing, has anyone had much success with using a one pass to sow the seed to save me a pass over the field?
Got a Kuhn-accord 3M seeder that I can use. I’m assuming I’d be best to tie the...
Need to replace the fan resistor on my JD as it only works on full blow at the moment [emoji100]. I’ve got the new part here but not sure of the location of the current fitted one. Is it in the cab roof? Remove roof top for access?
Thanks [emoji16]
Sprayed off 4 fields with rosate 360 @ 5 litres/ha and 0.5 l/ha of companion gold one week ago. 2 of the fields were stubble fields & the other 2 old leys. Plan is to re-seed them by discing them then power Harrow etc.
They haven’t haven’t died off as well as I’d hoped in the areas where there...
My iveco engined JCB JS130 was playing up lately. Found the 12v lift pump to be the fault. Priced JCB and they wanted £350 for a new one[emoji85]. After I regained consciousness from passing out I had a quick look on eBay to find something similar that I could adapt and hopefully make do.
Found...
Looking at buying a set of these.
Is it better to get the type where the lead roller is offset so that the rollers pull square?
Or will this greys type be fine?
Thanks [emoji1]
Hi, the PTO on our 6520 std has stopped working.
When u engage it with the yellow button nothing happens but the blue i light flashes up on the dash.
The driver doesn’t know if it happened at the same time as this issue - the top link arm pin came partially out and caught the underside of the...
Looking for some reviews of this product....
I’ve currently got a Trimble 500 sat nav that I’ve had for years and as it will be a long time before I can justify/afford an auto steer built in tractor I am looking at one of these units as a half way house.
Might have the chance of an ex-demo unit...
A wee winter project I’ve just got round to fitting up -
Can open and close both sides of the sliding door to set the right air flow into the calf shed depending on the weather.
2 x 8x4 sheets of 9mm stock board inside runners on the door frame.
The doors 16ft by 9ft 6”
We've a landcruiser Amazone 4.2L 2004 that's been too the moon & is on its way back.
Looking for a replacement that's a bit more economical on the old diesel[emoji85]
Maybe a 3.0 litre. Not keen on the look of the landcruiser lc4's etc.
Anyone got any good suggestions of a good replacement l?
Looking to change the coolant on old faithful[emoji1]. Can't find the operators manual[emoji848] is there an easy way of doing it or just a case of whipping the bottom radiator hose off? It's a Perkins engine version
I've always been under the impression that you couldn't have a petrol tank on your farm for safety reasons but someone recently told me the rules had changed. Is that correct?
Where would I source a good quality weld on Hardox wear plate? I'm need about 6ft for my excavator ditching bucket & a 8 ft piece for my telehandler grain bucket
Looking at both of the above new. The Kuhn is a 7501 and the KV is the 7-8meter machine. The KV is a bit dearer but it's got hydraulic working width adjustment and slightly wider.
Like KV stuff so leaning towards it. Anyone had experience with the KV rakes? Reliable?
Thanks [emoji3]
Looking into to buying one of these.... might just buy the starter kit with the bags etc to start with to see how we get on.
Anyone using one of these machines?
Thanks
I'm currently making a link box for the 3 point linkage for shifting calves around etc. It's mostly out of steel box section, I've welded an A frame too it that I got recently, only thing is the A frame(female part) came undercoated.
If I send the whole thing away to get galvanised will I have...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.