Fender switch problem

[Laurentiu]

I have a new holland t7060 autocommand, when i buy the tractor the fender switches for the 3 point hitch was missing,(to rise and lower the hitch) i buy both switch button and when i connect them to the wires connection and i push the button it doesn t happend anything, all the button in the cabin it working, i measured the switches wire and i saw that the electicity it s ok at the switches. The fender switches have two fuses( one with purple wires and one with brown wires) i put the buttons in both of the fuses and doesn t work.
I have 3 point hitch in front of the tractor and the outside buttons of them(the green ones) doesn t work too, when i push them to rise or lower the hitch doesn t do anything , just a sound like a ,,beep'' , inside the cabin.
I don t have a fault error or code error, on the monitor.
Someone have the same issue.
Anybody can give me an electrical graphic of the fender switches wire please?
I attached a few photos .

 

[del_boy]

You might need to go into the HH menu to activate the buttons. If they never had them and you've fitted them the option in HH menu will be 'off' im not sure which H menu you will need to access though im afraid

 

[Laurentiu]

The tractor had them but i think the owner took them, befor i buy the tractor...and the one in the front don t work too...

 

[del_boy]

Go into the H menu
Find U1 with the rear linkage symbol, got to H3. Find channel 2 and check its says 'yes'.
Check its enabled first
Same applies to the front linkage, U1. Find front linkage symbol. H3. Channel 1 yes, channel 2 yes. Channel 3 yes.
Hope this helps

 

[Laurentiu]

Ok thank you very much...i ll check that first, and post a reply

 

[Laurentiu]

How do i go to h menu? I need a 9 pin deutsch connector? Or i can enter without a 9 pin conector?

 

[del_boy]

How do i go to h menu? I need a 9 pin deutsch connector? Or i can enter without a 9 pin conector?

You need the calibration plug ideally. They can be bought. But failing that you can get some wire and stick into the plug to connect 2 pins but i have no idea which pins nor would i want to risk it

 

[del_boy]

This is the plug you need ideally

 

[Laurentiu]

Go into the H menu
Find U1 with the rear linkage symbol, got to H3. Find channel 2 and check its says 'yes'.
Check its enabled first
Same applies to the front linkage, U1. Find front linkage symbol. H3. Channel 1 yes, channel 2 yes. Channel 3 yes.
Hope this helps

I enter in h menu, i connect 2 pins with a wire and solved the front linkage, know it work, i didn t solved the rear linkage , what do you mean y ,,U1''? I have in h menu HS, RE, RM, JA, XA, LC. Whete i need yo enter? I find something with a linkage H3 chanel 1 ( here is showing a nomber 90, 100 , 110) , in chanel 2 i turn to yes , in ch 3 i turn to yes, but still rear linkage don t work. Where do i need to enter. In front of the linkage in H3 it was put on ,,NO''.

 

[del_boy]

HH menu. Scroll across until you find U1, go into this menu. Scroll across until you see the rear linkage symbol, go into this menu, find H3 go into this menu. The 1st channel 1 is the size of the rear lift rams in diameter, channel 2 is fender switch and channel 3 is the slip.
Sounds like your very close, its exactly the same procedure for the rear as you did for the front

 

[Laurentiu]

I didn t managed to do, i set all chanels to yes and still don t work...any ideeas?

 

[del_boy]

I didn t managed to do, i set all chanels to yes and still don t work...any ideeas?

Bugger. Check the wiring to the plugs, make sure both fenders are connected with no bad wiring. Are the switches you have fitted definitely ok/new?
Apart from that im not too sure, might be a dealer/ laptop job

 

[Laurentiu]

The switches are new.
Thank you

 

[Laurentiu]

By the way, after i do all that in H menu and start the tractor an error code comes up 12212 and P symbol apear, what is meaning? The tractor work fine but the error still apear

 

[del_boy]

By the way, after i do all that in H menu and start the tractor an error code comes up 12212 and P symbol apear, what is meaning? The tractor work fine but the error still apear

12212 is 'accelerometre not calibrated' the parklock may have lost its calibration, a low battery or a pause in cranking speed can cause a parklock error code

 

[Laurentiu]

I need to calibrate it? Or it will calibrate itsefl? How i calibrate it? In H menu ?

 

[del_boy]

I need to calibrate it? Or it will calibrate itsefl? How i calibrate it? In H menu ?

Im not too sure on this, its a bit past my pay grade. You need to get your hands on the calibration booklet, its all in there.
Ive attached a picture of the hh menu for u1

 

[Laurentiu]

Ok thank you, i ll try to find calibration booklet for t7060 ac

 

[Laurentiu]

I ve done it , with the calibration EPL
I wached a guy on youtube who done it
I have the same menu like him in HH menu

But the fender switches i cannot do it

 

[Laurentiu]

Hello again, today i clean up the fenders switches very well and now they actually work, but the switches isn t actionate the rear hitch , it s actionate one of the rear EHR , i have 4 ehr behind the tractor and when i push the fender switches one of the ehr is actionated, anyone know how to change the function from the ehr to 3 point hitch? I need to change the hose from the distribution oil pomp? I attached 2 photo to show you what hose is actionated when i push the fender switches