• Welcome to The Farming Forum!

    As part of this update, we have made a change to the login and registration process. If you are experiences any problems, please email [email protected] with the details so we can resolve any issues.

International 895 lifting ram

Toylexus

Member
Anyone know where I get a rear lifting ram for my 895. Theres two on them but I'm missing one.
Is there a left or right hand side or both the same?
Thanks in advance
 
Do you mean the assister ram on the linkage that was an optional extra to enable heavier implements to be lifted?

Not sure if I’ve ever seen two on a International.
 

Exfarmer

Member
Location
Bury St Edmunds
Either a breakers or I am sure CNH will sell a replacement but it will probably cost a fair bit.
Depending on what work you are doing, do you need the extra lift as it will slow the response.
 

Toylexus

Member
Thanks ex farmer. I lift potatoe boxes full of logs with a ripvator forklift. Cam manage ok as it is but I thought that maybe there should have been 2 on it
 

gmc541

Member
Location
Omagh
Anyone know where I get a rear lifting ram for my 895. Theres two on them but I'm missing one.
Is there a left or right hand side or both the same?
Thanks in advance
I am not sure if the left and right are the same or different. I have both although of a cx and are slightly bigger in diameter. Where are you based
Regards Gerard
 

Toylexus

Member
Hello gerard. I'm in n. Ireland. I would doubt they'll fit if there slightly wider as it's a pretty tight fitting. Will take a photo later.
 

gmc541

Member
Location
Omagh
Hello gerard. I'm in n. Ireland. I would doubt they'll fit if there slightly wider as it's a pretty tight fitting. Will take a photo later.
I'm sure that they will fit as they are the same back end. I have a 895 with twin assister rams also and will compare. I'm outside omagh so hopefully not far away
 

agrimax

Member
Location
Co Down
Left and rights on an 895 have different part numbers so presumably they are 'handed'. Both the same on a CX but different part numbers to the 895 also.However,they CX rams are listed as compatable with the 4200 series so you'd think they would do the 895!!:unsure:
 

essexpete

Member
Location
Essex
Left and rights on an 895 have different part numbers so presumably they are 'handed'. Both the same on a CX but different part numbers to the 895 also.However,they CX rams are listed as compatable with the 4200 series so you'd think they would do the 895!!:unsure:
Did CIH not beef up the lift on 4200 and CX?
 

gmc541

Member
Location
Omagh

Attachments

  • 20210604_223224.jpg
    20210604_223224.jpg
    334.1 KB · Views: 0

Toylexus

Member
Thanks everyone. I think the 895 lift rams are unique to that series. Cx is too wide and as u say gerard room is limited as to where they fit
 
Last edited:

How is your SFI 24 application progressing?

  • havn't been invited to apply

    Votes: 26 34.7%
  • have been invited to apply

    Votes: 13 17.3%
  • applied but not yet accepted

    Votes: 28 37.3%
  • agreement up and running

    Votes: 8 10.7%

Webinar: Expanded Sustainable Farming Incentive offer 2024 -26th Sept

  • 2,364
  • 49
On Thursday 26th September, we’re holding a webinar for farmers to go through the guidance, actions and detail for the expanded Sustainable Farming Incentive (SFI) offer. This was planned for end of May, but had to be delayed due to the general election. We apologise about that.

Farming and Countryside Programme Director, Janet Hughes will be joined by policy leads working on SFI, and colleagues from the Rural Payment Agency and Catchment Sensitive Farming.

This webinar will be...
Back
Top