Massey 6170 alarm mode?

Juris Logins

Member
Mixed Farmer
Hi, Got problems with my massey. It happened when i changed from front to rear. Šo the thing is that it,s stuck in rear low mode. dynashift level is not working abcd lights are changing but not properly. Front rear indicator is not working and other functions as pto 4wd and diff is not working, no lights on dash turn on while pressing buttons, speed indicator also is not working.
 

MF CI

Member
Hi, Got problems with my massey. It happened when i changed from front to rear. Šo the thing is that it,s stuck in rear low mode. dynashift level is not working abcd lights are changing but not properly. Front rear indicator is not working and other functions as pto 4wd and diff is not working, no lights on dash turn on while pressing buttons, speed indicator also is not working.

At the battery positive terminal check the wires going up to the two fuses, one red one yellow, its the yellow one you need tobe looking at. Make sure all connections and fuses are good with a big bulb not a multi meter or led tester. If good follow the wires over engine to the front of cabin then down and under cabin at front right hand corner. There maybe a connector to check along that wire. Removing the tin plate under the corner of the cabin find the yellow wire again and check connections there.
A good chance your problem is somewhere along there.

Edit. With the ignition off when you press the clutch pedal down do you get the red transmission oil pressure light come on? After releasing the clutch pedal it should go off after a few seconds
 
Last edited:

Juris Logins

Member
Mixed Farmer
At the battery positive terminal check the wires going up to the two fuses, one red one yellow, its the yellow one you need tobe looking at. Make sure all connections and fuses are good with a big bulb not a multi meter or led tester. If good follow the wires over engine to the front of cabin then down and under cabin at front right hand corner. There maybe a connector to check along that wire. Removing the tin plate under the corner of the cabin find the yellow wire again and check connections there.
A good chance your problem is somewhere along there.

Edit. With the ignition off when you press the clutch pedal down do you get the red transmission oil pressure light come on? After releasing the clutch pedal it should go off after a few seconds
At the battery positive terminal check the wires going up to the two fuses, one red one yellow, its the yellow one you need tobe looking at. Make sure all connections and fuses are good with a big bulb not a multi meter or led tester. If good follow the wires over engine to the front of cabin then down and under cabin at front right hand corner. There maybe a connector to check along that wire. Removing the tin plate under the corner of the cabin find the yellow wire again and check connections there.
A good chance your problem is somewhere along there.

Edit. With the ignition off when you press the clutch pedal down do you get the red transmission oil pressure light come on? After releasing the clutch pedal it should go off after a few seconds
I,ll check yellow wire and nothing happens when pressing clutch pedal, but i left tractor for night to rest. And guess problem dissapear. Lucky? No it repeated today again after operating an hour. It happens when changing front to rear.
 

MF CI

Member
No lights coming on when pressing clutch ??? It could be someone has done some re wiring and made it not standard. So turn on ignition, then press clutch, does the trans pressure light come on now. I am presuming the bulb in the warning light is working, this can be seen when the ignition is first turned on, all the warning lights come on briefly to check bulbs.

If the fault only starts after an hour's work and always when shifting into reverse it could be the solenoid.
 

Juris Logins

Member
Mixed Farmer
Usualy when it,s not in foult state there comes beep and i guess gearbox pressure light (red with chainring in symbol). When foult comes there is no reaction while pressing clutch
 

Juris Logins

Member
Mixed Farmer
Didn’t checked yet but probobly this require calibration, or there is problems with solenoids or posittion sensors.
 

Attachments

  • 45B06C75-B34A-4AE9-93F2-26250F89C13E.png
    45B06C75-B34A-4AE9-93F2-26250F89C13E.png
    764.3 KB · Views: 0
  • DAC73B9D-1DFF-453A-8D60-28B0B57B25E0.png
    DAC73B9D-1DFF-453A-8D60-28B0B57B25E0.png
    652 KB · Views: 0

Old Tup

Member
Errr
There is a PCB in a box under the right hand foot plate…..something sticks in my mind of something similar a good long time ago.
Dealer had one in stock (never a good sign) might Have been refurbed…can’t remember now.
But it was a long way home from the field in Low Reverse…it was dinner time…that bit is still crystal clear.
 

SFI - What % were you taking out of production?

  • 0 %

    Votes: 120 38.8%
  • Up to 25%

    Votes: 118 38.2%
  • 25-50%

    Votes: 42 13.6%
  • 50-75%

    Votes: 6 1.9%
  • 75-100%

    Votes: 5 1.6%
  • 100% I’ve had enough of farming!

    Votes: 18 5.8%

Expanded and improved Sustainable Farming Incentive offer for farmers published

  • 251
  • 1
Expanded Sustainable Farming Incentive offer from July will give the sector a clear path forward and boost farm business resilience.

From: Department for Environment, Food & Rural Affairs and The Rt Hon Sir Mark Spencer MP Published21 May 2024

s300_Farmland_with_farmFarmland_with_farmhouse_and_grazing_cattle_in_the_UK_Farm_scene__diversification__grazing__rural__beef_GettyImages-165174232.jpg

Full details of the expanded and improved Sustainable Farming Incentive (SFI) offer available to farmers from July have been published by the...
Top