Good evening,
I have a Bomford 457 Hedge Trimmer which has a spool block set up for open centre hydraulics. I run it on a John Deere 2140 which is closed centre hydraulics.
Is it possible to convert the spool block to closed centre? Having read a few hydraulic threads it would seem @Mr Happy...
Does anyone know where I could add a free flow return on the back end of a John Deere 2140? For running a bale wrapper or log splitter for example.
Thank you
Ransomes 51 Marquis cylinder mower for sale. Used to use it to keep the lawn looking incredibly tidy and short. Has a new fuel tank, runs well. Started this morning in a couple of pulls after being fuelled. Not been started for a while but mowed ok.
£150 buyer collects, its large and heavy!
Good afternoon,
After many years of service my rather old KM22 parted with a drum yesterday morning. Is there any value in any of it for parts or is it all heading straight to the scrap man?
I have decided that repairing it probably isn't going to be cost effective, as it had a fault before...
Secondhand John Deere JS63 mulching mower. In good condition, starts first pull of the cord. No longer used as we now collect the grass clippings, so I have decided to sell it.
Has a homemade fix on the self propelled cable, these seem to be the weak point of the machine.
£150
Thank you
We have an old slurry tanker with a spare 6" opening blanked off. We are think of using it as a large mobile water tanker for watering a nursery.
Looking at this NC tanker there is a smaller fitting to the right at the rear. What is this called? Who sells them? Struggling to find such a...
Hi,
With the hazard warning switch in place, the flasher unit is constantly ticking, but the indicators don't flash. I can replicate by removing the hazard warning switch and putting a piece of wire across 15 to 45. This is technically off, but allows the circuit to operate i.e. lets you use...
Hello,
Does anyone know how you adjust the amount of string the baler puts on a bale? It seems to be putting on far too much string at each side. For comparison it used a new pack (2 reels) on 20 bales.
Thank you
Does anyone know of any UK based baler breakers? One of my knotter frames broke apart yesterday while I was looking at a knotting issue. A new replacement from John Deere is rather expensive, I could get a pattern one from Woodfields which are significantly cheaper. Looking at the weather, may...
Tonight my John Deere 342 bent one needle back on itself under the baler ram. Why or how did only one needle manage to get bent? I would have thought that if the timing had gone wrong both would have got bent. Removed the bent needle and finished by tying off the last ones by hand as the other...
Hello,
I have a set of 8ft chain harrows which you drag on a chain behind the tractor. These work ok but they are forever building up a large amount of trash when used.
I have looked at secondhand spring tine harrows as an alternative, one of the benefits I see is being able to pick them up at...
Is the disc in front of the Subsoiler leg meant to have any movement/swing on its axis? Just wondering if it should or not, it's in line with the leg so if it should but is seized it won't be an issue.
Hi, what is the best solution here? The studs are rather rusty and the plate does not want to move much. Do I continue hitting it with a hammer? Don't want to damage anything in the gearbox. Or something to prize between the two outer plates?
The fuel gauge on my John Deere 2140 has taken to reading full to the brim recently. Is this going to be a bad earth? Worn through wiring somewhere? Has always worked well until recently.
Hello,
Does anyone still run or used to run a 90 inch rotavator? If so what size (up) tractor was on the front? Would an old John Deere 2140 stand a chance of powering it? Standens documentation states up to 90 hp at the PTO for the 90 Powervater.
Looking for one for small area grassland...
Does anyone top grassland at this time of year to reduce the amount of grass going into the winter? I am asking as I only make hay once in the year usually July or August time so now the land has quite a bit of regrowth on it.
I was wondering whether there would be any benefit to mulching it...
I am thinking about applying some Fertilizer to our hay meadows as nothing has been put 'back in' for quite a few years.
What would be a good rate to apply kgs/acre.
I am also thinking I would be better of with some thing like 20-10-10 rather than straight nitrogen.
Thanks.
Having made hay for the last few years on our meadows I have the feeling that the land ought to have something put back in. So I am looking at an older fertilizer spreader to put something like 20-10-10 on. I have seen a Teagle XT 22 relatively close by on ebay and an Amazon ZAU 1501.
I know...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.