Abrasive Discs

I've had a re-stock of discs and thought i'd put them all in one thread rather than try to update all the original ones as some prices have changed a little. It'll also be easier to mix and match this way.

All prices exclude VAT and delivery. Delivery cost is dependent on weight and delivery postcode.

Norton Neon 115mm (4.1/2") 40 grit Zirconium flap discs, pack of 10- £9.00 per pack
Norton Blaze 115mm (4.1/2") Rapid Strip Discs- £5.20 each
Dronco Attack 115mm (4.1/2") 1mm thin cutting discs, expiry date 2022, pack of 25- £9.50 per pack
Dronco Attack 115mm (4.1/2") grinding discs, expiry date 2021, pack of 10- £8.50 per pack
Dronco Attack 230mm (9") 1.9mm thin cutting discs, expiry date 2022,- £1.10 each
Tyrolit 230mm (9") 1.9mm thin cutting discs, expiry date 2022,- £1.30 each

Orders of 2kg or less usually sent via Royal Mail, heavier orders via APC or ParcelForce.

Please message with your requirements and a delivery postcode for a delivery cost.

 

[the-mad-welder]

Only 350 of the 115mm cutting discs left.

 

[the-mad-welder]

Bump

Nearly out of the Blaze discs now.

 

[Robert K]

Norton Neon 115mm (4.1/2") 40 grit Zirconium flap discs, pack of 10- £9.00 per pack

Any of these left if so I'll have one pack please

 

[the-mad-welder]

Still stock left at the same prices. I am running low on blaze discs though.

 

[the-mad-welder]

I'm out of Norton Blaze and the Norton flap discs now.

I do have some imported (Chinese, not to everyone's taste I know!!) 40 grit flap discs. They work out at £6.50 inc vat per pack of ten. I can get one or two packs in a Royal Mail 2nd class delivery for £3.50 inc vat.

They are not as good as the Norton ones but this is reflected in the price. I do use them myself and i'd say that you'd use three of them where you'd use two Norton Neon ones, but thats just me, it obviously all depends on how you use them.

 

[Robert K]

Have you got any cutting discs in stock

 

[Flat 10]

What’s current stock @ mad welder? Needing to place an order.

 

[the-mad-welder]

What’s current stock @ mad welder? Needing to place an order.

Bit sparse at the moment to be honest.
I have the Dronco 4.1/2" grinding and the Chinese 40 Grit flap discs priced as in this thread.

I have no 9" cutting discs and the only 4.1/2" cutting I have are some Intergrind ones which work out at £11 ex vat per pack of 25. Not sure how many I've got, I can look tomorrow.

 

[the-mad-welder]

Prices for Dronco cutting discs to follow shortly, I shall make enquires!!

 

[Flat 10]

Thanks. I want 4inch cutting, grinding and flap.

 

[the-mad-welder]

Right, I've ordered some more Dronco cutting discs and am able to hold the prices as per the start of the thread. All the lines I currently have available are below.

The Dronco cutting discs should be with me within the week hopefully. I've listed the 9" as individual discs and as a pack at a slightly better rate as it saves splitting a pack. I'll add the expiry dates for the cutting discs when I get the stock but they will be at least 2022, probably longer.



All prices exclude VAT and delivery. Delivery cost is dependent on weight and delivery postcode.

Dronco Attack 115mm (4.1/2") 1mm thin cutting discs, pack of 25- £9.50 per pack
Dronco Attack 115mm (4.1/2") grinding discs, expiry date 2021, pack of 10- £8.50 per pack
Dronco Attack 230mm (9") 1.9mm thin cutting discs,- £1.10 each
Dronco Attack 230mm (9") 1.9mm thin cutting discs, pack of 25 - £26 per pack
Imported Chinese 40 Grit Flap Discs, Pack of 10- £5.42 per pack

Orders of 2kg or less usually sent via Royal Mail, heavier orders via APC or ParcelForce.

Please message with your requirements and a delivery postcode for a delivery cost.

 

[Steevo]

Worth doing 125mm discs too if you can get stock.

 

[the-mad-welder]

Worth doing 125mm discs too if you can get stock.

I tend to only buy what I use myself then I never get stuck with stuff that 'need' to sell.

However, a pack of 25 Dronco attack would be £11.50 ex vat if I buy in at least 10 packs.

If I can get orders for 5 Packs from somewhere, I'd chance my arm or perhaps just buy a 125mm guard for one of my grinders!!

How many can I put you down for?

 

[Steevo]

There’s logic in that.

I like 125mm as they last longerand can cut through something a little bigger. I had some steel water pipe to cut the other day in a hole and a brand new 125mm disc was only just enough.

I bought some the other day in fact....a pack of 5 from Screwfix to get me out of a hole. £5.99!!

I then picked up a pack of 25 Parweld from Amazon for £11.95 delivered tho I see they do them for £9.70 currently. (Inc vat). Makes your ex Vat Dronco prices seem good value I think even with delivery on top.

I’d happily have a pack or two next time I need some

 

[David.]

If you had turned the water on, you could gave floated yourself out of a hole .

 

[Dave W]

I've had a few packs of the chinese flap discs and think they're excellent for the money.
I barely use grinding discs nowadays

 

[Captain Slack]

Is there any market for 3in and 7in flap discs

 

[Robert K]

The selection I had last time I ordered have outlasted some of the Screwfix discs

 

[the-mad-welder]

Blatant bump!!

Plenty of 115mm and 230mm cutting discs in stock and ready to dispatch.