Connor bale wrapper, problems, again.

[Greythundercloudys]

Yesterday my wrapper stopped tipping them of properly in auto, put oil in the tractor, but didn't help much at all, a real pain, probably need to send box to King's but wrong time of year for that, was thinking the bales were heavier with the welger but it was nice stuff, not wet. It just needs to go 6inchs more.

 

[nonemouse]

Have you enough oil flow from tractor? Our old case tractor needs lots of revs on to tip heavy bales (Connor 3pt linkage model)

 

[Pigless]

Yesterday my wrapper stopped tipping them of properly in auto, put oil in the tractor, but didn't help much at all, a real pain, probably need to send box to King's but wrong time of year for that, was thinking the bales were heavier with the welger but it was nice stuff, not wet. It just needs to go 6inchs more.

If its a static wrapper like mine, I put a couple of bits of 7*3 timber under the front so it works on an angle. Can also tension the belts to make it tip the bales of easier.

 

[Greythundercloudys]

Tractor just ticking over is alway been fine in the past.

 

[Greythundercloudys]

Yes tried the planks of wood at front aswell.

 

[Zebbedee]

Tractor just ticking over is alway been fine in the past.

Probably best with a few revs on it

 

[Greythundercloudys]

Thinking that aswell.

 

[Greythundercloudys]

This is defo the last year of this machine, its still bursting the plastic with the bale coming over to tight on to a bobbin, bobbin is brand new, only way to solve it is another machine. So bloody annoying.

 

[oil barron]

This is defo the last year of this machine, its still bursting the plastic with the bale coming over to tight on to a bobbin, bobbin is brand new, only way to solve it is another machine. So bloody annoying.

Put up a picture of it almost finnished the cycle.

 

[Greythundercloudys]

I will, the next day lm at it.

 

[Greythundercloudys]

One from last year, put new bobbin on but still does it, not everytime.

 

[Dave W]

Not familiar with Connor but I'd guess there will be a tip off time in the settings somewhere. That will need increasing by half a second

 

[oil barron]

If the bobbin is still at the same angle, that’s your problem. It should be flat against the end of the bale.

 

[nonemouse]

Not familiar with Connor but I'd guess there will be a tip off time in the settings somewhere. That will need increasing by half a second

Not sure on the OP’s one but mine uses RDS box looking the same as the mchale, various settings can be changed on it.
the bobbin should be straight up, not angled like the one in the pic

 

[Dave W]

If the bobbin is still at the same angle, that’s your problem. It should be flat against the end of the bale.

Agreed. That bobbin is completely wrong. The centre axis is about 15deg over centre away from the bale. At the very least it should be vertical or just over centre towards the bale

 

[oil barron]

Agreed. That bobbin is completely wrong. The centre axis is about 15deg over centre away from the bale. At the very least it should be vertical or just over centre towards the bale

Looks like it’s had a few dunts with the squeezer

 

[balerman]

That bobbin should tip inwards towards the bale slightly so the side of it is parallel with the bale.Set the way it is,it’s bound to rip bales.

 

[Tim G]

Heat the mounting plate and bend it back.

 

[KB6930]

Your new baler has a slightly wider chamber so that won't be helping

 

[Greythundercloudys]

The man from Connor said going buy the pics the angle of the bobbins shouldn't make much difference really, but obviously does, they've been like that since l bought it, l never bent it.