Hi folks new member here we farm on Dartmoor and have decided to start baling our own small bales
However access is tight short of a helicopter dropping us in a baler we're looking for as small an old conventional baler as we can find.
Or an inline if we can find/afford it
What model should...
Hi just been pricing fert after a wet miserable lambing ... normally buy 25.5.5.... 20.8.11 was mentioned in conversation, never used it and it'd obviosly higher in p an k ....on a mixed livestock farm that makes round baled hay and silage and puts muck on thru winter would a 20,8,11 be a good...
Not a big user, only ordered 8x600kg bags of 20.10.10, delivered12th April and kept in shed till today, first 2 bags had set almost solid all the way through not rock hard and managed to break it up enough to get it out of the bag with a piece of 3x3 wood but took about 20 mins.
Next 2 bags...
My ih 584 is having hydraulic problems
Thers a small leak around the steering wheel and a small leak at top ram seal on front loader they started a couple of months back and I'm going to get done with the fine weather however today all hydraulics went faulty back end juddering up front loader...
Anyone on here built water troughs from Ibc's?
Any photos would be great
I've got some off ground with no water that I'd like to graze with youngstock so thought an ibc connected to a water trough ibc would be ideal as its portable around the paddocks as I graze them down?
Following on from the 'Tractor Chat' video from a few weeks ago, we're looking for some willing volunteers to appear in some similar videos, preferably in Yorkshire for logistical purposes!
Please feel free to DM if you prefer or reply in the thread below
Be gentle... ignorant arable farmer asking for a friend on this one...
Let's say you had £25k, and wanted to get into livestock.
You have access to low imput permanent pasture (heavy land), and occasionally some rotational leys. You have access to a loader,
You have an old shed, potential...
Have a 2010 5470 with suspended font axle, that does this bang when 4wd disengages - not sure if it’s coming from front axle, rear diff or somewhere else.
Feels like massive torque wind-up in the drivetrain and worse when a load on / at speed and in 2wd then brake (4wd comes on) lift foot off...
Is it just me or is most of the adverts just scams. Browsing through 7 seaters and fairly new peugeot 5008 for 3-4 k, volvo xc90 for similar money. Do they think were stupid. How is this still alowed to go on
Hi,
I'm considering the clipper posts to use with sheep netting.
I liked the idea of moving the posts, but the anti-lift plate would make that very difficult apparently.
Are the Clipex post harder to remove than wooden stakes?
Clipex do the PASTURE post without the anti-lift plate BUT as I...
I’m after making a ad lib feeder for brewers grains I wouldn’t have thought they’d flow in a normal ad-lib barley feeder any suggestions appreciated cheers
Anyone now the timing procedure for re fitting injection pump to a 2009 mc power 6 its a ftp/iveco engine .
Pump should come back timed up just wanted to now if there were any timing pins etc
Thanks
Hi all not sure what other people think to new machinery but in the last couple of years it’s been pretty shitty with problem after problem but mainly paint.
Not going to mention any names but paintwork why does it keep dropping off?
I’ve had new diggers and after a year the paint work literally...
Lets start in 1970, with 6 of us from Reading University did a trip round Turkey
Threshing scene
Gearbox layshaft gave up along the south coast, we got a replacement into Istanbul, Roger and I took a bus to Istanbul to get it through customs while Steve drove on 4th gear and the red knob to...
Anyone ever had wire break like this before? Had this in 2 spots were barb and rylock split, along with a few spots where the bottom 2 wires are broken. Has it been cut or is it possible for it to break like that?
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.