Kuhn sw4014 hyd lines

[paul&mandy]

If you're running on a SCV you may need to increase your oil flow slightly.
Sounds like the knife arms aren't getting enough oil before the next function begins.

It's at 100% already. Perhaps I'll try a few more revs. Don't know will play about more when I get going properly

 

[KB6930]

All you'll need is a couple of 27mm to 1/2 or 3/4 adaptors and qr couplers to put it onto power beyond . I'm not sure of the LS lone size thread but it'll not be bad to fund out

 

[Ted]

It's at 100% already. Perhaps I'll try a few more revs. Don't know will play about more when I get going properly

100% on the valve flow coming out of the tractor or 100% in the calibration setting?

 

[Ted]

If you’re calibrated at 100% and all the other wrapper functions are working correctly, then it could possibly
be as @d williams has suggested that the “ knife arms down” setting needs extending .
I can plug ours in tomorrow and look at some settings in the Service Menu.

 

[d williams]

It's at 100% already. Perhaps I'll try a few more revs. Don't know will play about more when I get going properly

Revs won’t be it the timing on the knife needs adjustment
What size bales you wrapping?? Wouldn’t worry how many you have to do my boy was waiting for one to drop off back baler

 

[paul&mandy]

100% on the valve flow coming out of the tractor or 100% in the calibration setting?

Cal setting

 

[paul&mandy]

Revs won’t be it the timing on the knife needs adjustment
What size bales you wrapping?? Wouldn’t worry how many you have to do my boy was waiting for one to drop off back baler

80x90

 

[d williams]

80x90

No problem to it if didn’t have to put plastic on finish with the baler

 

[Ted]

Couldn't find any settings in the Service or Dealer menus that would alter Film Arm down settings.
Myself, I think you need more oilflow.
Try giving it some more oil over and above your calibrated value.
Seriously, if you can spare an hour, get your Hydraulic man out and get the tractor fitted for Load Sensing. It'll be like night and day.

 

[paul&mandy]

Couldn't find any settings in the Service or Dealer menus that would alter Film Arm down settings.
Myself, I think you need more oilflow.
Try giving it some more oil over and above your calibrated value.
Seriously, if you can spare an hour, get you Hydraulic man out and get the tractor fitted for Load Sensing. It'll be like night and day.

Hi, I spoke to the chap from Kuhn yesterday that set me going. Someone from service supposedly can help me sort it over the phone but no one called back yesterday.
Was a pain yesterday as I had to keep an eye on it and keep going into manual to fully close the cutters.
Also completely different do you find you run out of plastic 1 side way before the other? I can wrap 2 more bales with 1 spool before there both empty.

 

[Ted]

Yours is a later model and will probably have the newer hydraulic valve block.
Check the OC/CC selector screw is screwed right out for C/C
Wouldn't be the first time one has turned up here with it wound in.

 

[Ted]

 

[Ted]

Hi, I spoke to the chap from Kuhn yesterday that set me going. Someone from service supposedly can help me sort it over the phone but no one called back yesterday.
Was a pain yesterday as I had to keep an eye on it and keep going into manual to fully close the cutters.
Also completely different do you find you run out of plastic 1 side way before the other? I can wrap 2 more bales with 1 spool before there both empty.

No, generally pretty much even give or take a turn or two.
Had a 3135 FBP Film Binding unit that always ran out one side earlier than the other. Never did get to the bottom of it.

 

[paul&mandy]

Kuhn man has checked that.
Need a bloody manual. It's vanished after pdi. Thought they would have got me at least a print off by now.

 

[paul&mandy]

No, generally pretty much even give or take a turn or two.

Wonder why that is then... I'll put a mark on satalites see if it's always the same 1 later.

 

[Ted]

Yeah, Digital is fine until you want to flip through it to find settings etc.
Give me a book any day.
If you register on My Kuhn you can load up your Kuhn machines and download Operators manuals, parts etc.
Not much help when you've got bales out everywhere.
I hate new machines...

 

[paul&mandy]

Yeah, Digital is fine until you want to flip through it to find settings etc.
Give me a book any day.
If you register on My Kuhn you can load up your Kuhn machines and download Operators manuals, parts etc.
Not much help when you've got bales out everywhere.
I hate new machines...

Im just looking at the my Kuhn. Will download it when I have the serial no.

 

[Ted]

Wonder why that is then... I'll put a mark on satalites see if it's always the same 1 later.

Check you have the same stretch gears fitted to both units.
Ours has 22/36 giving 60%
Option is 21/37 for 70%.

 

[Spencer]

Hi, I spoke to the chap from Kuhn yesterday that set me going. Someone from service supposedly can help me sort it over the phone but no one called back yesterday.
Was a pain yesterday as I had to keep an eye on it and keep going into manual to fully close the cutters.
Also completely different do you find you run out of plastic 1 side way before the other? I can wrap 2 more bales with 1 spool before there both empty.

That’s your film not the machine. Some brands run out together some and way off. If you want to get into service menu the password is 5

 

[Spencer]

Just don’t go messing with too much stuff in there