Yep the buggers sometimes do that here as well. Maybe not a bad thing as it forces me to clean the water troughs out regularly.Sometimes i do that, but they always seem to push the straw in the water tank, every time
Michale V660 net wrap problem
- Thread starter Drillman
- Start date
dannewhouse
Member
- Location
- huddersfield
having problems with pollen/ dust build up on the netwrap a funny fix that we were told about for a jd 575 net problem every new net blather it in talcum powder and the feed roller as well then you don't get any grief.
we started using covernet and all problems stopped after that. covernet seems the best for my new holland 640 as well wont feed the black and white netwrap in just does the middle 2ft nowt else
we started using covernet and all problems stopped after that. covernet seems the best for my new holland 640 as well wont feed the black and white netwrap in just does the middle 2ft nowt else
Bring this back to life,
1st time out this year the other day, first 50 or so bales no bother but after that it refused to feed net into bale chamber.
all the rollers That net goes round nice and shiny and rubber one pulling net in as it should but net not making it to the bale chamber.
anything I’m missing?
2017 machine
1st time out this year the other day, first 50 or so bales no bother but after that it refused to feed net into bale chamber.
all the rollers That net goes round nice and shiny and rubber one pulling net in as it should but net not making it to the bale chamber.
anything I’m missing?
2017 machine
Is that the netter with the adjustable tension from the cab ?
dannewhouse
Member
- Location
- huddersfield
Has it got a build up of chaffy dust in the right hand door where the belt that drives the better is?
Good starting spot.
If you get off and look while it should be netting the belt be slipping because chaff holds tensioner off
Chae1
Member
- Location
- Aberdeenshire
There's 4 rubber strips these bend back sometimes. Make sure these are straight.
Another thing is make sure feed roller is swinging in. Ours stopped doing that.
Make sure the knife isn't in. This doesn't let net into chamber.
No that’s on the newer version
No that side of things is all running Bob on.
new belt and plenty belt grip product on it as well (unwanted wifeys xmas talc from a rarely seen distant relative)
Feed roller swinging in
tell me more, your second person who’s said that and I think its the problem but not entirely sure how it works
Chae1
Member
- Location
- Aberdeenshire
If you look in the side where duplex chain turns rotor you can see its range of travel. Net can go round the end of roller not letting if fully swing in. Also check the belt is okay that drives the roller. Take the belt off and turn it by hand, have had bearing go on that roller too.
If you put it into manual and just power net drive, where is net getting too, bunching up?
Net I can reach down over top of plate that goes over net roll between net rollers and belts and get hold of it and pull it further into chamber.
Obviously when baler is shut off
dannewhouse
Member
- Location
- huddersfield
That moving feed in roller isn't rotating I've had that before.
If you watch while it's supposed to be netting off the belt maybe spinning but the roller and pulley isn't. Had same fault
TripleSix
Member
- Location
- Helmsley, North Yorkshire
Have you tried shouting at it?
dannewhouse
Member
- Location
- huddersfield
Kicking it also works well ...
Hitting it with a spanner and then throwing spanner on the floor is the ultimate fix if nothing else works.
Yep tried all the usual swear words,
TripleSix
Member
- Location
- Helmsley, North Yorkshire
That's me all out of ideas then
I used to get this a lot on my first McHale I had to stop till the pickup cleared then net manually for no apparent reason but it worked
Just been out to shed for another look at it and think I fixed it,
one of the belts for netting system wasn’t on a pulley right
everything looked to be running right from the cab And no One to observe with panels open and netting cycle engaged to see if owt was up with it.
one of the belts for netting system wasn’t on a pulley right
everything looked to be running right from the cab And no One to observe with panels open and netting cycle engaged to see if owt was up with it.
dannewhouse
Member
- Location
- huddersfield
Ours has started comeing up with knife overpressure warning randomly, not using knives at moment but hit a bump and it will be beeping and carry on, any suggestions?
- Location
- Le Veurde, Allier, France 03320