- Location
- nottingham
Can't fault the cayena until it gets too sticky for the tyre packer so a sabre time would be perfect to take over in dodgy conditions , havnt rolled much behind the cayena
Sorry I meant drills without a packer with my slugs/pre-em comment, at least with a packer you get some firming action. What’s tine spacing on the Amazone? Always liked the look of them and surprised there’s not more about...are they pricey?Can't fault the cayena until it gets too sticky for the tyre packer so a sabre time would be perfect to take over in dodgy conditions , havnt rolled much behind the cayena
165 , the tyre packer works a treat and consolidates well , it just ticks a lot of box's , fairly easy to pull , good calibration , accurate seed rate and depth , will drill into most seedbeds or DD , got split tank so putting fert down the spout with nearly everything now , last time I looked at new was 70k couple year ago. Think a sabre tine would work well with it but cost would dictate a cheaper tine drill as back upSorry I meant drills without a packer with my slugs/pre-em comment, at least with a packer you get some firming action. What’s tine spacing on the Amazone? Always liked the look of them and surprised there’s not more about...are they pricey?
Just had a quick google; very smart! Saw quite a few pics with in-line disc openers at the front? Assuming that’s an option rather than standard-would be about as low disturbance as you could get with a tine drill is the rubber sausage auto-reset on the coulters up to the task when it’s really tough going like this spring and you’re going deep for beans etc? Same applies to sabre-tine to get back to the OP!165 , the tyre packer works a treat and consolidates well , it just ticks a lot of box's , fairly easy to pull , good calibration , accurate seed rate and depth , will drill into most seedbeds or DD , got split tank so putting fert down the spout with nearly everything now , last time I looked at new was 70k couple year ago. Think a sabre tine would work well with it but cost would dictate a cheaper tine drill as back up
It's perhaps not as bad as it looks, it's not overly thick but sure they could have used less if they'd made it from box section and angle, but modern drills have to be laser cut in swoopy shapes for aerodynamics! The lower section does hold the fan, and the steps themselves are what I'd describe as adequate, nothing more. Our previous drill was a Sumo Versadrill, if you want excessive metal that thing took the biscuit, unbelievable.So much metal simply for the set of steps.
There's no tines directly in front of the wheels, the tines that cover where the wheels run are behind them. The wheels also have scrapers, if they pick up mud it's from the tractor tyres moving the surfaceDo the sabre tines run into trouble by having depth wheels behind tines, so running on freshly moved ground?
I agree there are designs that do a more thorough job, but a 3m Claydon or Triton would be beyond what we could pull, the Sabre is quite easy on the HP. Certainly I stopped drilling at one stage when the seed was going to be left in an open slot filled with water, whilst the neighbor opposite carried on with a Claydon and it worked fine. However they have a lot to do so they have to crack on, I only have a bit to do so I had a couple of days off and came back when it had dried up a bit. As with everything it's horses for courses, and it suits our systemGenuinely would rather have a triton as the leg design is far superior to get water away (it’s a really good concept I think shame that some of the marketing was ridiculous a couple years ago!)
Which DD did you go for BB?It’s definitely been my saviour this year, drilled about 80% with it. Doesn’t hurt to have a look though. Just bought a disc dd.
I think I would agree. need more HP though as the tines are working a lot deeper.Genuinely would rather have a triton as the leg design is far superior to get water away (it’s a really good concept I think shame that some of the marketing was ridiculous a couple years ago!)
Yep, but then if you want to drill regulary late into wet that’s the trade off as you probably need that deeper slotI think I would agree. need more HP though as the tines are working a lot deeper.
Is there anything not to like about the new Sabre Tine?
BB
Genuinely would rather have a triton as the leg design is far superior to get water away (it’s a really good concept I think shame that some of the marketing was ridiculous a couple years ago!)
Nodoes the sabre tine have any sort of break back option for the tines in stony ground at all ?
does the sabre tine have any sort of break back option for the tines in stony ground at all ?