yes ,fitted it myself not long ago. clevis and ball hd one. can prop it when up as well for safety
Car lift for clutch replacement
- Thread starter Bury the Trash
- Start date
- Location
- 200 miles N,NW of New York
Depending what you think on the carwhy not that sounds quite a good idea
john432
Member
- Location
- Carmarthenshire
Fill some bags with loose straw to put under the front for protection as you lift it..oldish no value car.. what's to loose...garage often costs more than the car is worth.
need something on the front to soften the blow because the wheels will have to be off /drive shafts out/ ie front wheel drive
Rich_ard
Member
AS-4T36 Mobile 4 post parking lift - Automotech Services Limited
The AS-4T36 is the ideal lift for vehicle storage when space is tight. The lift can be moved within minutes with the aid of the mobile wheel kit provided. The perfect lift for Classic car restoration enthusiasts as the lift can also be used as a conventional 4 post lift. Features: Lifting...
automotechservices.co.uk
A 4 post for just over 2k
Didn't suit me, because of room taken up in workshop and easier to, for eg, weld a sill on without the platform in the way. But on plus side, perhaps doesn't need such good floor to bolt to?AS-4T36 Mobile 4 post parking lift - Automotech Services Limited
The AS-4T36 is the ideal lift for vehicle storage when space is tight. The lift can be moved within minutes with the aid of the mobile wheel kit provided. The perfect lift for Classic car restoration enthusiasts as the lift can also be used as a conventional 4 post lift. Features: Lifting...
A 4 post for just over 2k
I got one same as Nealy above, just got new cables to fit sometime. Think about £160/pr.
SilliamWhale
Member
Rich_ard
Member
Could you lift a small trailer with yours. A flat bed or such like
Nearly
Member
- Location
- North of York
specs say 200mm. I went 250mm because I could.
SilliamWhale
Member
Did you pour a whole floor at 250mm or just put in pads?
Nearly
Member
- Location
- North of York
dug out a section full width x 2.5m.
It was on an existing slope so just took the sloping stuff out and re-concreted level.
used stocks of rebar and 2.5cube so base heavier than any load.
Don't see why not, so long as the wheels pass between the posts. The 4 legs extend enough to reach the four jacking points on any car I've tried, so will probably reach the four corners of an 8ft trailer body.
TheTallGuy
Member
- Location
- Cambridgeshire
BASIC CAR ROLLER CHASSIS TILTER RAMP PIVOT CAR LIFT CJAUTOS CT01 4 Stud | eBay
ITEM CODE CT01 4 stud. A car can be turned by one person using an engine hoist or block and tackle. AXLE STANDS ENGINE CRANE AND CAR NOT INCLUDED. The CJ Autos Basic Car body Roller puts the car on its side and lets you work standing upright.
www.ebay.co.uk
Has the benefit that all those lost coins and pens will reaper from under the seats!
Nearly
Member
- Location
- North of York
I lifted a cattle trailer with box section through the side vents.
It was the bast way to get the side arms above the wheels to sort the brakes.
- Location
- 200 miles N,NW of New York
Blimey, that's to clean to work in
Netherfield
Member
- Location
- West Yorkshire
@Clive did say a few years ago.Blimey, that's to clean to work in
spin cycle
Member
- Location
- north norfolk
reading some of the replies blimey......I thought I was a 'harem scarem'
- Location
- 200 miles N,NW of New York
He must have a cleaner
Blimey, that's to clean to work in
not the farm workshop - it’s my workshop at home !
we have a pit in the farm workshop - just re painted the floor last week
tidy environment = tidy work imo
