Will be laying a stone base for a new shed soon, rather than hire a laser level thought I might buy one, loads on ebay for £50.
Any good? Any recommendations? Thanks.
A new to us Trimble FM-1000 with ISOBUS unlock with our some years old Horsch Pronto DC Combi Seeder.
Task Controller seems to be OK for Section and Rate Control. Latest firmware on both gadgets.
But to our disapointment we do not get any sound alarm from the FM-1000 when the seed of fertilizer...
Is there any way to set a 34i to run at a set pressure for say 5 seconds when I switch the booms on? I find when backing into a corner or starting on a awkward run I have to switch over to manual and bump the pressure then switch back to auto once I'm up to speed.
My previous sprayers were all...
Is it possible to run a vaderstad drill control box from a speed signal other than the drill's radar? ie the tractor GPS or wheels speed sensor
The radar has failed on our carrier bio-drill and rather than get that repaired I'm wondering if we can simply use a different (more accurate) speed...
on the screen of my AGCO c300 this message appeared "No touch screen driver found" after trying to update to version 3.17.707. does anyone know how to answer what can that be?
Need a bit of help re the above. We have a topcon hyper ag base station.
It was all working well and correction signal was always in the green and sub 2cm. On Friday when we set it up for the days work it would not see any statalites, ie base was flashing red for stat and then the same on...
Got a AGCO/Topcon AGI-4 works with EGNOS Geen correction and GNSS signal, turn it to RTK I get Green cell signal and Ntrip corrections but GNSS is red with 8 or 9 Satelites worked OK a couple of weeks ago when power-harrowing.
Have some satelites gone awol or something?
We took delivery of a new RO-EDW sower in recent days and a mechanic from the sales company called out today to give us a run down on how it works.
While going through the boundary settings he mentioned that they had manually adjusted the geo-point to 5m. He said that they'd found the...
We have just had a software upgrade in our 724 to unlock Contour Assist which works fine.
However we now have a problem where a trailed implement when operating in a dead straight line maps askew to the tractor. Not in an offset manner but the left hand side further back.
This is ok if you're...
Considering buying a Topcon TT weigh to use with my grain trailer. Has anybody got any experience of one? I know they won't be as accurate as a full weighbridge but i can't justify a weighbridge.
I run a front tank accord df2 with Rds radar etc mounted Claydon tool bar. Just drilled a field calibrated as normal finished field to realise 80kg/ ha out ... on seed used ... checked calabration it’s bang on. Wtf .. what could possibly be going on.. the speed on the screen said the same as...
Hi all,
i own a Fendt 718 SCR which came wit a built in Topcon AGI-4 GPS , on EGNOS . I've wanted to upgrade it to RTK and i found a radio module
that i bought. Now when i opened the reciever, i noted that the IMU (the gyro module) was not installed , even do i have gyro readings on my...
I have identified a possible second hand MF 7722. It’s auto steer ready so what are my options for getting gps on it, preferably with enough accuracy for drilling? I had been looking at putting a retrofit Fieldbee system on my NH7040 but if I go for the MF I will presumably only need a receiver...
Good morning friends, I'm new to the group, from BRAZIL! sorry if you are breaking the rules of the group! Does anyone know where I can buy the TOPCON C3000 Touch Screen, the one that goes over the LCD display, here in BRAZIL it is impossible to find replacement parts!
I'm not sure if the X30's...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.